11047711800 Kenmore Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- DAVID from HARRAH, OK
- Parts Used:
- WPW10730972
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
would not drain or spin
Replace water pump
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from Gardena, CA
- Parts Used:
- WP8183202
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door would not close, piece on the bottom of the hinge that pulled door in was broken.
Remove the two screws holding the hinge to the washer body. Lift up on the hinge to remove from the washer. Remove all the screws holding the inner door piece to the outer cover. Remove the old hinge, replace with the new one. Put the two door pieces back together and tighten the screws. Place hinge back in on the washer body and push down. Replace screw at top and bottom. Close door and start using.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- kevin from elizabethton, TN
- Parts Used:
- WPW10730972
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
Washer washed cloths then would not rinse
Just went by instructions provided by parts web site
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from Rock Hill, SC
- Parts Used:
- WPW10121596
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Divider Broke
I just put the divider in the dispencer
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Norman, OK
- Parts Used:
- WPW10110225
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Water flow problem resulting in f20 error code
Unplugged electric cord and turned off water supply. Remove 3 screws @ rear of washer and removed top panel. Removed clamps on hoses and electrical connector to flow meter, removed and replaced with new flow meter. Replaced the top panel, turned on water supply and plugged unit in. Finished in less than 15 minutes. Saved myself several hundred $
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Julie from Milton, PA
- Parts Used:
- WPW10730972
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Drain Pump Stopped working
Took of the panel, unscrewed the old drain, screwed the new drain in. Very very simple to do! The first part I received leaked, I called customer service and they gave me a refund and express shipped a new part - no questions asked. Very good customer service!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JANICE from MANHATTAN, KS
- Parts Used:
- WPW10110225
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
I was having the hf code constantly beeping and couldn't run a full cycle.
I opened the top by taking four screws from the back and lifted the top. The part to be replaced was clearly in view. I opened the clamps on the hoses, pulled the hoses off, removed the wires, and reversed the process with the new part. The washer works great now! I ordered the part on a Friday, and it was delivered the next day, even though I didn't pay for overnight!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- brian from turners falls, MA
- Parts Used:
- WPW10730972
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
buzzing noise water not draining
unplug washer from outlet carefully tilt back to get at underside of washer remove bottom panel. pump location lower right front. remove two hoses from back using pliers keep note on hose location. remove two bolts on underside of machine slide pump to the right to release from rubber holders to install reverse the process also good idea to use the new hose clamps that come with your new pump and the rubber mounts if they are included
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- lou from stamford ct, CT
- Parts Used:
- WPW10110225
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
HF code durring cycle
Removed top of washer and replaced flow meter.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JOSE from OZONE PARK, NY
- Parts Used:
- WP8182119
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
The Bellow of my washer machine was broken
I watched video first and it help me a lot to do the repair myself of my washer machine and i save about $ 1,500 dollar. Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Anderson, SC
- Parts Used:
- WPW10388414
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
drive belt slipping
Old belt and new belt were not exactly the same. did research and deturminded that the new belt was correct. Reomoved the back panel and rolled the old belt off. Pully is designed to allow changing of the belt without taking the pully off. Put new belt on the motor pully ensuring it was in the groves. started belt on the drum pully and turned it untill it was tight. With an open hand I held the belt on the drum pully so it would not slip off and gave the drum a quick turn to jump the belt onto the pully. rotated the system several turns to make sure everything tracked correctly. Replaced the back panel.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anthony from Avon Lake, OH
- Parts Used:
- W10289554A
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
needed to install shipping bolts
Read the instructions provided by PartSelect.....and with a bit of patience I installed all four bolts so the washer's inside agitator was not damaged in shipping. I highly recommend that anyone who is moving/storing or shipping their washer that you find the correct shipping bolts according to your model and make and install them prior to moving your appliance.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from Waco, TX
- Parts Used:
- WPW10730972
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Wouldn' drain f21 then after I drained it it gave f33
Replaced the pump assembly. The different type of clamp supplied in the kit was very helpful.
Was this instruction helpful to you?
Thank you for voting!
Bellow had a large hole in it, and was letting water drain out all over the floor.
It was a little difficult to put the new Bellow in place on the tub, due to the fact you have to basically push the outside of the Bellow all the way into the tub so you can install the tub clamp. The other difficult part of the task was tightening up the clamp it's self. There really isn't a lot of room to move your hand around in the space you are given to work. But after a few hand cramps and a few things said, that are not needing repeated, I was able to get the clamp tight. Once you have the clamp on the tub, it's basically pretty simple to slide everything else into place. The wire/spring clamp that is used to attach the Bellow to the front of the washer is fairly simple to put into place with a little patience. All in all it was a cheep and easy repair for a due-it-your self repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tina from Denver, PA
- Parts Used:
- WPW10730972
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers, Wrench set
needed to replace water pump
dryer stacked on top of washer. had to lift washer and block w/2 x 4 to get under unit and replace pump
Was this instruction helpful to you?
Thank you for voting!