11047781701 Kenmore Washer - Instructions

Looked at how the old drain pump was installed, then removed it and installed the new one. It was a fairly simple fix. The only feedback were that the parts picture was a little confusing becuase the picture didnt really look like the actual part, so we were unsure if we were ordering the correct part.

Took the outer ring off with the help of pliers just be careful. Push the bellow into the washer. We cleaned the area good at this time. Put the new bellow in being sure to keep the wrinkles out and securing it in place with the other clamp. Make sure to keep it lined up and wrinkle free to prevent leaks and possible tears later on. You will need the screwdriver to tighten the screws in the inner clamp.

The difficult part was getting the water from the washer without making a huge mess. I used a shop vac loosened the cover on the filter/strainer assembly use the shop vac to suck up the water before spills all over. if the tub is full I dumped my shop vac twice total. 1 Remove pedestal drawer 2 removed lower cover to expose mechanicals and pump assembly 3 vac out the water by using above procedure. 4 rotate hose clamps to a position where you can get the needle vice grip on them/remove hose clamps. 5 lift cover exposing electrical connections on the pump assembly depress tab slide connector out. 6 remove 1 torx head screw securing pump to base of washer. 7 remove pump assembly. 8 Reinstall in reverse of above instruction. I also took the lower tub hose off and washed, bleached along with hot water to. clean it

I started by dismounting the door from the washer, then placed the door on a flat counter with a towel underneath to avoid scratching. I unscrewed all the bolts securing the the frame. Once the frame was removed, I dismounted the broken door hinge and secured the new one in reverse order. Just a little time and patience. Job completed with no mess!

I removed the old pump and replaced it with the new one. I am the happiest person on earth right now to have my washing machine working at its best again. Thank you so much.

Replaced water pump

Old belt and new belt were not exactly the same. did research and deturminded that the new belt was correct. Reomoved the back panel and rolled the old belt off. Pully is designed to allow changing of the belt without taking the pully off. Put new belt on the motor pully ensuring it was in the groves. started belt on the drum pully and turned it untill it was tight. With an open hand I held the belt on the drum pully so it would not slip off and gave the drum a quick turn to jump the belt onto the pully. rotated the system several turns to make sure everything tracked correctly. Replaced the back panel.

repair was a cake-walk with the video there to help.Thanx

I followed the instructions and it was surprisingly simple. Glad I didn't call the "handy-man" since it was easy to do it myself as a handy-woman!

Removed top of washer and replaced flow meter.

I watched video first and it help me a lot to do the repair myself of my washer machine and i save about $ 1,500 dollar. Thanks

Took old one off and put the new one on. Was very easy. Hardest part was disconnecting hose clamps, which was still easy

took front panel off. Pump is right there easy to work on. Used pliers to take 2 hose clamps off. Used star screw driver to take 2 screws off of pump and removed old pump. The Assemblely goes the same way but the drain hose coming off the tube is not very easy to get back on. Hose is flimsey and the stem, on the end of the drain pump isnt long enough to keep hose on while tring to slide hose clamp back on.

Read the instructions provided by PartSelect.....and with a bit of patience I installed all four bolts so the washer's inside agitator was not damaged in shipping. I highly recommend that anyone who is moving/storing or shipping their washer that you find the correct shipping bolts according to your model and make and install them prior to moving your appliance.

Unplug the power first.If you can lean the washer bank and support it with something underneath to make it easier to work on.Removed the 3 bolts at the bottom panel underneath the front door. Pump is right there in front. Unplug the power connection first,you can also remove the wiring that is right in front of the pump so it will be out of the way. remove the pump from it mounting grommets and pull it out a Little so you can get to the hoses at the back of the pump. Using pliers to pull of the hose clamps you can pull off the hoses. Now you can remove the pump out. Do everything in reverse and that's it. I found it to be easier than I thought and took less then 20 mins.