11016984500 Kenmore Washer - Instructions

Removed the old hoses and screwed on the new hoses.

I removed the cover for the softener dispenser on the top of the agitator. Then reached in and removed the cover of the nut and washer which was very sticky and sealed with an o-ring. This took a bit of pressure. Then used a socket wrench with an extension to loosen the bolt and took the whole agitator out of the machine. Then I set the agitator on the floor and with a fine 12 inch long screw driver released the catches while turning and pulling the agitatior with my other hand and holding the lower agitatior on the floor with my feet. I then turned the upper part over and removed the cogs and holding mechanism.
Then I reversed the process after replacing the cogs with the new part. 25 minutes total.

Found leveling spring loose on bottom of washer, the sheet metal on bottom of cabinet ad rusted through. Drilled new hole in sheet metal and installed new leveling spring. Greased hole with blue marine grease so it will last another 40 years.

First I screamed at the ceiling, because I have a three year old and an infant, and the washing machine was dead. Then I went to youtube. It seemed like the "agitator dogs" were the issue.

In this spirit of any repair, I replaced them, and it was not the issue. I don't know what I expected.

Ceiling. YouTube. Pacing.

Then I figured it was this part - the motor coupling. I unplugged the machine and took out the drain tube. I leaned the machine back and propped it up with an empty detergent bottle, because those were abundant. Ratchet off a few bolts and the motor comes out. The coupling was indeed broken. The new one slips right in - I tapped it a few times with a mallet for good measure / vengeance. Ratcheted the bolts back on and tipped it back up.

Pros: Washer works now.
Cons: Everest-esque laundry pile to address.

But hey, it worked! I am no handyman and it wasn't too bad at all. Half hour tops.

Put new one on work good, but now can't pump no more .the problem now is the spin cycal broke and I not going to fix it. Thank for the part work good.

removed water lines from back of washer. tilted washer to get access to the pump/ removed 2 hoses at pump and removed to snap clips attaching the pump. easiest repair i ever did. washer works fine now.

I loosened two screws which held the knob panel in place. I undid the two clips holding the cabinet and removed it. The pump has two clips holding it on, I removed those and the pump came free. Taking advice from these forums, I did not remove the hoses attached. I disconnected the wiring harnesses from the motor. The motor has 2 clips also, these being held on with screws. I removed the screws and the clips. THE MOTOR IS HEAVY.
You will see the coupling on the "spindle" of the motor. In my case, both plastic pieces were cracked in 2 places. I removed the old coupling and cleaned the "spindles" and lightly regreased.
The replacement pieces I ordered were the "improved" ones with the metal insert. They were a tight fit on the motor but I used a socket and hammer. (lightly). Line up the coupling pieces, reattach clips, DONT FORGET THOSE SCREWS HOLDING THE MOTOR CLIPS. Pump goes on next, etc. MAKE SURE ALL WIRING IS RECONNECTED! Cabinet goes back on, large clips holding cabinet to rear of machine go back on. Knob console flipped down and reattached.
Plugged it in and I was good to go! This washer is almost ten years old and this is the second time I have been able to bring it back from the dead, the first time being the agitator "dogs" wearing out. THANKS PARTSELECT!

We had to take the motor out and remove the coupling, when putting it back together we had some problems because the washer was on its side and the lid was open. After putting the motor and coupling back together we tried to turn it on, unknowing to us the lid was open so nothing would happen, finally we realized the lid was open. The actual repair was not complicated, just human error made it seem than way

I had given up on repairing the machine and placed order for a $650 washer. After returning to home from this shoping, I wanted to know possible problems with the current machine and came across a story on your web site attached to the Coupling parts description. It described the repair details. Encouraged I placed order for this $15 parts and repaired in an hour, saved the replacement machine cost. Thanks a lot

Tipped the washer onto it's side, used pliers to loosen clamps on old hose. Removed outer drain hose from white plastic hose adapter on back of washer. Removed white hose adapter (snaps out of place) and old hose. Fed new hose through opening for white adapter, then snapped new adapter into place on back of machine. Put the new hose in place and replaced clamps. Sat washer back upright. No more leaking! It was easy and didn't take more than 15-20 minutes.

I am an old woman who is disabled and without any tools or knowledge, but sheer stubbornness and will power, I waited for my tools and other parts to come in, in the mean time I fixed my young neighbors whirlpool washer, well We took top off the nut I had already pre assembled her cam so set it in place of old one put bolt back in place and the top of agitator she says works perfectly now, my parts came in I had nothing to remove as my handicap daughter had already thrown away all the loose parts, I threw away old top agitator, assembled cam and put in place still did not feel tight enough so added seal from other nut!! it worked tight enough, put the inner part back in with new part and soap put the top back on and now works good as new, was disappointed could not put bottom agitator in place, just not strong enough lol well this was my story

Started taking machine apart, would of been easier if I had looked at the online diagrams first, but dismantled enough to find a few broken parts, I could not tell the coupling was broke till I actually removed the water pump and motor. Total cost for 3 plastic parts was less than $25 including shipping. Received parts in 3 days on standard lowest cost shipping. Put machine back together, with just a few extra screws and wire clips, but machine works like new now. Much better than the cost of new or used washer.

Being female & never working on appliances, it was a challenge for me. I took the spinning unit apart: 1) Outer cap 2) Inner cap 3) Screw, nut & bolt popped out. Rusty & wouldn't lock into place anymore. Ordered nut & washer at about $10 + shipping. Total $17 from MayTag Rec'd right at 7 days via USPS. Used nutdriver/wrench to screw in new bolt w/washer. Wah la! That did it! Washer working great now! Now that I'm a "diy" handy person, I'm ready for my next challenge. Hopefully, none!

We unscrewed the two screws at the back of the control panel. Holding the control panel on both ends
we pulled it toward the front of the machine, slightly and gently lifting it at the same time, removing it from the metal surround. Holding the control panel up off of the surround we rocked the surround forward and lifted it off the washing machine frame.
We could see where the leak was coming from. We took the hose clamps from the two ports, then
using a pair of pliers pulled the two clips that are holding the pump onto the shaft protruding from the
electric motor. We matched up the part on the web sight. Ordered the part then when it came in we just reversed the order putting the machine back together. The hardest and most time consuming
thing about this repair was the clean up of the washing machine. (Dirt and soap residue does
build up on the inside of the wash tubs.)

leaned washer back on wall at or more than 45degree undid two screws off of motor. pulled old part off put new on reinstalled motor Done