11047882700 Kenmore Washer - Instructions

After diagnosing codes noticed no drain replaced pump asm

This was so easy to swap the parts out. The plastic hooks that hold the pieces inside our washer had just worn out. We put our washer and dryer through LOTS of use and I am amazed it has hold on this long! The broken piece just popped out and the new piece just snapped right in. Thank you for your speedy shipping and the great price.

I did not replace the pump body. I just removed the motor with the 3 screws. Put the new one on. This way I did not need to mess with the hose clamps.

The drum baffle came off. This website provided a diagram to make ordering the part easy. It was reasonbly priced and came in the mail very fast. I had it installed in my washer within 5 minutes. Excellent experience. Thank you.

replaced drain pump.Saved 200$

The new piece just took seconds to install. You had to set the piece slightly farther back then where it belongs, and with a slight downward pressure, just slide the part toward yourself until you hear it click into place. About 5 seconds and no tools required.

I unplugged the power and tilted the washer back and removed the kick panel. I then unscrewed the pump trap access and set aside. I used the shop vac to remove the remaing water from the washer to the drain pump, unplugged power to the pump, removed the discharge hose and suction hose. After everything was removed, I removed the pump. Everything I read said to take the pump loose before removing everything, it just worked better for me to take everything loose with the pump secure. Going back together I mounted the new pump, plugged it back in (I did not have to remove anything from the plug to use it on the new pump as the insert indicated), installed the discharge hose and the suction hose. I found it easier to rotate the clamp a bit on the sucttion hose to allow me to use my right hand to depress the clamp to get it back in place. Replaced the kick panel, lowered the washer back in place, plugged it in and ran it through a cycle, worked great.

Unplugged electric cord and turned off water supply. Remove 3 screws @ rear of washer and removed top panel. Removed clamps on hoses and electrical connector to flow meter, removed and replaced with new flow meter. Replaced the top panel, turned on water supply and plugged unit in. Finished in less than 15 minutes. Saved myself several hundred $

Very simple repair. Lined up the baffle tabs with the drum slots. Pushed the tabs into the slots, pulled the drum baffle towards the opening of the wahser until it seated. You will hear aclick.

Very simple repair had to remove door from Washer, loosen the seals so that I could remove the old hinge. Inserted new hinge place the door and hinge on brackets and tightened the screws. I was very pleased with the fast action in getting me my parts, less than 24 hours.Thank You.

Very limited access to the bellow clamp. Found it easier to first remove washer front panels (8 screws total), providing ready access to R&R the bellow. 40 minutes tops.

Removed the 3 bolts attaching top of washer. Disconnected hoses from the inlet value and flow meter, also very careful to remove the wire connections. Removed Water inlet valve (this requires the star screw driver). Did find it best to connect the inlet valve and flow meter before reattaching the inlet valve, as that sits under the lip, it is just a bit of a tight fit to get the hose reconnected between the two. Then reconnected the flow meter hose to the dispensing box, reattached the hoses and ran a cycle no f20 issues, as a note, an f20 has to do with a restriction in the flow of water not with pressure so not sure if it was the inlet valve or flow meter clogging up or both.

I removed the top 3 screws on the rear, removed soap dispenser, removed screw in front corner at soap dispenser,pry off control panel with flat head screwdriver lay on top, removed spring around bellows at door opening, remove 4screws holding door assembly, disconnect 3 molded plugs serving door lock, you will need to hold door while you loosen bellows clamp.Reverse process note: soap dispenser tube can be removed to clean without any tools. It is some much easier when you remove the front door assembly.T-20 torx screwdriver, 9/32 socket Theirs a you tube video also.ghw

A real novice at dyi. Found what the error code meant in the manual and google searched it online. Found Youtube video on repair and was successful in getting the washer to work a few times before the error code returned. Decided to replace the inlet valve and on your site took the advice of a previous user and also changed the flowmeter. Could not have been a better experience. Easy to find the correct parts for my model and got great tips...plus your shipping was excellent. Thanks!

Disconnect the hot and cold water supply hoses from the rear of the machine. Remove 3 screws in the rear that fasten the top cover. Slide the cover rearward and remove it. Disconnect the black outlet hose and unsnap the two electrical connectors from the water valve. Remove one screw that fastens the water valve to the rear panel. Slide the water valve away from the screw and remove it. Reverse this procedure to install the new valve.