11049972602 Kenmore Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Steve from TULSA, OK
- Parts Used:
- WPW10352973
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Washer would not fill
replaced actuator switch. It did not fix the problem. Replaced actuator arm, and fixed. Needed the switch because gears were stripped. Needed the arm because it seems over time, the arm straightened, thereby increasing its length so that the rotation of the switch bound up during its cycle.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Tonawanda, NY
- Parts Used:
- WP8183270
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Door would not lock
Did the repair just like the video on your website. Was really easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kimberly from Lake Stevens, WA
- Parts Used:
- WP8183202
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Couldn't be any easier!
I am a 63 yr old woman. I was able to remove the washer door, take off the broken hinge, install the new hinge, and place it back on the front of the washer in less than 15 minutes! It is a front load washer and designed for one person to do this. I YouTubed a less that 2-minute video first. The hinge fit perfectly!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Big Torch Key, FL
- Parts Used:
- WP8181794
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers
water inlet valve leak and hose
disconect wayer inlet hoses.remove screws that hold the top cover. This will expose the water inlet valve. remove the defective valve and any other associated clamps,hose etc. test run for leaks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brenda from PLYMOUTH, IN
- Parts Used:
- 280187
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Socket set
WASHER WOULDNT DRAIN F21
REMOVE HOSES AND POWER PLUG REATTACH EVERYTHING AND THEN DONE.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jimmy from MEMPHIS, TN
- Parts Used:
- WP89503
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Old hot water inlet hose had budge at both ends.
Turn water off at the inlet valve of hose you are replacing. Disconnect inlet hose the washer and let water drain out in a bucket. Then remove old hose. Replace new hose to inlet valve then washer . Use pliers to tighten both ends. Turn on water to check leaks at both ends of hose.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Salt Lick, KY
- Parts Used:
- WPW10467289
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Washer posting a f6 error
This was an easy fix . PartSelect was quick and had all the info I needed to repair my washer. Plus shipping was super fast. Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Howard from Boynton Beach, FL
- Parts Used:
- 350930
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Both outside door handles turned very beige
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Houston, PA
- Parts Used:
- 280187
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Washer fails to drain water
First I want to acknowledge Parts Select for their prompt delivery(received parts in less than two days)and their unbeatable prices(approximately 1/3 less than two local appliance repair/parts shops). Repair was straight forward a simple swap of the pump and I saved quite a few dollars.Thanks Parts Select.Any future appliance parts needs will be purchased here.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Chino HIlls, CA
- Parts Used:
- WP8182119
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Bellow torn at bottom - significant water leak
Very limited access to the bellow clamp. Found it easier to first remove washer front panels (8 screws total), providing ready access to R&R the bellow. 40 minutes tops.
Was this instruction helpful to you?
Thank you for voting!
Washer leak and tear on clothes
It was easy as soon as I previewed a video on how to repair bellow it was all about unscrewing some screws and removing some parts but was simple steps that anyone can do themselves only thing that gave me very little trouble was putting the spring coil around the bellow needed my husband to help me a little so it wouldn't come out place while stretching the spring to make sure everything was good and secure and ran a test washer to make sure it didn't leak afterward.the baffle was very easy to replace with very little pressure I was able to slide it till I heard a click sound and it was secure did laundry same day and every was wonders very happy I was able to save some money on labor :)
Was this instruction helpful to you?
Thank you for voting!
Bellows stained
I removed the top 3 screws on the rear, removed soap dispenser, removed screw in front corner at soap dispenser,pry off control panel with flat head screwdriver lay on top, removed spring around bellows at door opening, remove 4screws holding door assembly, disconnect 3 molded plugs serving door lock, you will need to hold door while you loosen bellows clamp.Reverse process note: soap dispenser tube can be removed to clean without any tools. It is some much easier when you remove the front door assembly.T-20 torx screwdriver, 9/32 socket Theirs a you tube video also.ghw
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Douglas from Pflugerville, TX
- Parts Used:
- WP8182862
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Wrench set
Tub filling with water when unit turned off
Disconnected power. Turned of the water supply. Removed/disconnected the water lines from the washer. Removed the top by removing three screws. Disconnected the wires/connectors from the valve assembly. Disconnected the water line from the valve assembly to the dispenser assembly. Removed the screw holding the valve assembly on. Installed the valve assembly and reversed the above procedure.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Troy, MI
- Parts Used:
- 280187
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Water smells bad if washer sits for a few days.
I replaced the pump thinking this was the most likely cause of the problem. The pump is easy to access and get to. The reviews were helpful. The hose clamps were difficult to get back in place especially the one from the washer drain to the pump (need wide-jaw pliers). Now that I have seen the system work, the pump was not bad and the water from the drain still smells bad. I just ordered the filter 8181683, which looks like the only other thing that would prevent the water from draining completely. The drain hose is not blocked.
Was this instruction helpful to you?
Thank you for voting!