11027032600 Kenmore Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Elijah from Point Hope, AK
- Parts Used:
- W10193886
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Socket set, Wrench (Adjustable)
UL flashes, will not spin, really loud,& black spots under washer
We ordered the outer tub & bearing and now the washer works like it was brand new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joaquin from Santa Clarita, CA
- Parts Used:
- W10820048
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
Washing machine was rocking a lot, and stoping too much.
Our washer wasn't really working, we called a tech to diagnose our problem, he charged us $35 to let us know that we had a suspension problem, he promised to call us back next day with the estimate for the repair, he never did. So I decide to search, I found a video showing exactly how to do it, it was a very easy, and simple process that I decide to order the parts my self. The parts were delivered to my door in 24hrs. I installed the parts in less than 45 min, and now our washer is working like new again!!!
Thanks guys.
Thanks guys.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- david from knoxville, TN
- Parts Used:
- W10183157
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Socket set
washing machine showed F50 code
I watched a video on how to do it.it wasn't very difficult the hardest part was getting the machine out of the laundry room and laying it over
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Shawn from Indio, CA
- Parts Used:
- W10820048
- Difficulty Level:
- Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
Washer was noisy and had a lot of movement
The rod kit fixed the issue. I cant really explain how I did it, because I dint know if I did it the right way.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jose from Verobeach, FL
- Parts Used:
- W10536347
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Socket set, Wrench set
Won't drain the water
It was not easy but I dit my sell
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janet from Colfax, WI
- Parts Used:
- WPW10072840
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Replace a seal
Just had to remove cap on agitator and replace new rubber seal.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ralph from New Milford, NJ
- Parts Used:
- WPW10074580
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The seal was broken on the agitator cap barrier
Removed the fabric softner at the top of the agitator (needed a screw driver to pry it loose) and reached in to grab the barrier with my hand and pulled it out, very simple to do.When I put the new one in I put some liquid soap on the gasket and it snapped right into place.Very easy to do, all is well now, thanks Part Select.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gregory from Sandy Springs, GA
- Parts Used:
- WPW10072840
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lots of gunk between fabric softener dispenser and where it attaches to the agitator
Rubber O ring around the Inner Cap was rotted and busted through. Replaced with new Inner Cap Seal. Easy as pie!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mike from castlewood, VA
- Parts Used:
- WP8533540
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Broken retainer
How did I repair? I opened the box removed the part, handed it to my wife with a 1/2" nut driver and she installed it in 1 min.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jacob from Glennville, GA
- Parts Used:
- W10536347
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
washer would not drain water
need to get washer turned on side where you can work underneath the machine. This job is alot easy if you get where you can see good and have plenty of room to work. You have to unhoook the wire from the old pump and then take the two mounting screws off from there you unhook each hose by squeezing clamp together and sliding backwards away from pump. A pair of needle nose pliers can make this process easier if the clamps are turned in an hard to get to position. You mount the new pump the same way as taking off the damaged pump. Take a screwdriver to help you slide the clamps up onto the new pump makeing sure the sleeves are completely over the new pump fittings and the clamps are slid up evenly, so you want have any leaks. Then replaces wiring harness and mounting screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- richard from asheville, NC
- Parts Used:
- W10536347
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
replaced leaking pump
Easy repair. Went to You Tube and saw PartSelect video. The best instructions...should make a link from parts page to video of install. Also replaced Heat element on Dryer. Watched video first.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- william from germantown, TN
- Parts Used:
- WPW10189966
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
washer wouldn't go in the spin cycle-
Pulled washer from back of wall and disconnected power source. I removed three screws in back that houses the ol motor control board. Also, I had to pull the front control knob off so that I could lift the cover to expose control board. I took several pictures of the motor control board before unplugging the wires just in case I forgot where the wires needed to go. Very simple process and had machine working within 15 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lorraine from Millsboro, DE
- Parts Used:
- WPW10072840
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
broken seal
went well but alas the problem still exists.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- axel from lighthouse point, FL
- Parts Used:
- W10820048
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
drum made loud noise
put machine on side pushed old rods out to top installed new ones. runs like new. tried to ask mechanics or stores nobody would help with info, they all want to send mechanics with 80$ just to get here. it was easy to do. thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janelle from Gray, ME
- Parts Used:
- W10536347
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
water leak at pump, crack in pump housing
First off always remember to empty all pockets, coins etc ruin pumps.shut off water supply, unhooked water lines and drain into pan.tilted machine forward so i could work on pump which is located lower left. drain pan under pump area, removed 2 rubber water hose's 3 5/16 screws with nut driver. Very carefully un clip rear of housing and removed wire harness. installed new pump
Was this instruction helpful to you?
Thank you for voting!