Models > 11047711801 > Instructions

11047711801 Kenmore Washer - Instructions

Jump to:

All Instructions for the 11047711801

Customer:: EMMANUEL from CLINTON, MD
Parts Used:: WPW10253483
Difficulty Level:: Easy
Total Repair Time:: 1- 2 hours
Tools:: Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set

Timer was not advanced due to door lock failure

Searched internet for diagnosis. Ran diagnostic test using the diagnostic manual from whirlpool. The error code was F29. Replaced door latch but problem was not solved. Then order the Motor Control Unit. Removed old control unit through the top by removing the top washer cover and numbering harness positions with painter's tape. Install the new Control Unit and ran diagnostic procedure. The problem was solved. The washer is working fine.

Was this instruction helpful to you?

Customer:: kevin from elizabethton, TN
Parts Used:: WPW10730972
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Nutdriver, Pliers, Screw drivers, Socket set

Washer washed cloths then would not rinse

Just went by instructions provided by parts web site

Was this instruction helpful to you?

Customer:: Antonio from La Puente, CA
Parts Used:: WPW10730972
Difficulty Level:: Easy
Total Repair Time:: 15 - 30 mins
Tools:: Pliers, Screw drivers

My washer would not drain, weird noises, etc.

This part worked great! Completely fixed all the problems that I had with my washer. A bit hard to actually place it in(pliers are necessary) but otherwise very easy to install.

Was this instruction helpful to you?

Customer:: John from Drexel Hill, PA
Parts Used:: WPW10730972
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Pliers, Socket set

The drain pump cracked over the winter

After unplugging the washer, the unit was pulled forward and tipped backwards, I placed a 2x4 under the washer to serve as a brace. I removed the existing bolts holding the old pump in place, removed the spring hose clams, unplugged the pump and removed the damaged part. inserted the new drain pump, re-inserted the bolts and tightened them, replaced the spring clamps with "regular" hose clamps supplied with the replacement part, plugged in the power supply, removed the brace, pushed back the unit and plugged it into the outlet. From start to finish - about 20 minutes. Was running wash about a half hour after I started.

Was this instruction helpful to you?

Customer:: Todd from Cherry Valley, IL
Parts Used:: WPW10730972
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Nutdriver, Pliers

No drain fault code F-21

Very --simple remove front acess panel -- open sump clean out remove water out of existing pump an hoses with small wet dry vac -- remove small wire harnes --cut band clamp on discharge with side cutter --remove inlet -suction side of pump hose clamp with channel locks --un bolt two screws on bottom side of washer with 5/16 nut runner --discard old pump reinstall new one in reverse order --only takes about 20 mins total !!! ---

Was this instruction helpful to you?

Customer:: WILLIAM from SAINT CHARLES, IL
Parts Used:: W10822553
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Nutdriver, Pliers

washer jumping when spinning

open the front bottom panel (3) screws. remove panel. twist off old shocks by turning the shock counter clockwise. reinstall shock by turning clockwise.

Was this instruction helpful to you?

Customer:: Dagmar from Edwardsville, KS
Parts Used:: WPW10730972
Difficulty Level:: Easy
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers, Socket set

Wouldn't drain

I was already very familiar with the motor & drain pump, as I had disassembled my original one in attempt to find the problem & fix it. Finally, I broke down & purchased a new one. It was VERY easy to install! The most difficulty was finding the right sized board to put underneath & raise the machine up (with the dryer attached to the top of it) to place the board underneath so that I could tighten the bolts from underneath to attach the pump. After that was over, the rest was cake! Just attach the hoses & the electrical, which just clips in place & my washer is like new again! Yay! Oh, and yes, I'm a woman DIY'er.

Was this instruction helpful to you?

Customer:: Chris from Spanish Fort, AL
Parts Used:: WPW10730972
Difficulty Level:: Easy
Total Repair Time:: 15 - 30 mins
Tools:: Pliers, Wrench set

Washer wasn't draining and spin cycle not working

Followed instructions from a You Tube video. I'd recently lost my job and money is tight and I thought we could save money doing it myself. By watching the video and ordering parts from you we were able to save $500 between parts and labor. Thanks

Was this instruction helpful to you?

Customer:: JOSE from OZONE PARK, NY
Parts Used:: WP8182119
Difficulty Level:: Easy
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers, Socket set

The Bellow of my washer machine was broken

I watched video first and it help me a lot to do the repair myself of my washer machine and i save about $ 1,500 dollar. Thanks

Was this instruction helpful to you?

Customer:: Tina from Denver, PA
Parts Used:: WPW10730972
Difficulty Level:: A Bit Difficult
Total Repair Time:: 15 - 30 mins
Tools:: Nutdriver, Screw drivers, Wrench set

needed to replace water pump

dryer stacked on top of washer. had to lift washer and block w/2 x 4 to get under unit and replace pump

Was this instruction helpful to you?

Customer:: laveda from juneau, AK
Parts Used:: WP8182119
Difficulty Level:: Easy
Total Repair Time:: 1- 2 hours
Tools:: Screw drivers, Socket set

hole in bellow

pulled the front and top of the machine off, pulled off the old bellow, ordered the new bellow, and put the new bellow on. we looked on youtube.com for a video on repairing the machine.

Was this instruction helpful to you?

Customer:: Winifred from Livonia, MI
Parts Used:: WP8182119
Difficulty Level:: Very Difficult
Total Repair Time:: 1- 2 hours
Tools:: Pliers, Screw drivers, Wrench set

Bellow had mold and mildew

Found it impossible to get the bellow off the machine. Removed the front spring. Even tried to but off the bellow. No luck. Called repairman. He had to take off the front panel, door panel, and the top of the machine before he could remove the back spring/clamps.

Was this instruction helpful to you?

Customer:: Steven from Kalamazoo, MI
Parts Used:: WPW10730972
Difficulty Level:: Easy
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers, Socket set

The washer was flashing f-21 code. And the cloths were soaked.

First thing, unpluged the washer. I removed the lower front acces panal. I then propped the washer up on 2 pint sized paint cans to reach the pump mounting screws. I disconnected the wire bundle going to the pump. Then removed the inlet and outlet hoses from the pump. Then I removed the 2 mounting screws on bottom and slide the pump to the left and removed. I then pump the new pump on the same way I took the old one off, but in reverse. Easy and fast the worst part was the price of the pump.

Was this instruction helpful to you?

Customer:: James from Hopewell, NJ
Parts Used:: WP8182119
Difficulty Level:: Easy
Total Repair Time:: 1- 2 hours
Tools:: Screw drivers

Front Bellow Moldy

Followed video, slowly. Was easier then I expected. Everything fit perfectly.

Was this instruction helpful to you?

Customer:: Charles from Murphy, NC
Parts Used:: WP8182119
Difficulty Level:: A Bit Difficult
Total Repair Time:: 1- 2 hours
Tools:: Socket set

Bellows were moldy and underneath had mold

We hired a local repairman and he even had trouble . I would not suggest anyone trying this installation on their own. It took the repair guy an hour to do and he struggled. Not an eary installation

Was this instruction helpful to you?

All Instructions for the 11047711801