11021392012 Kenmore Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Douglas from BEECH ISLAND, SC
- Parts Used:
- W10780048
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Springs worn out on the suspension rods. (Noisy drum in spin cycles)
The video posted on this site will walk you right through the repair. Great service. Thanks!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dan from KISSIMMEE, FL
- Parts Used:
- W10780048
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Washer shaking and banging loudly during spin cycle
Replaced the suspension rods
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jerry from OROVILLE, WA
- Parts Used:
- W10780048
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
Extreme imbalance
This washer would not go into spin cycle without going out of balance no matter how we arranged the contents in the drum. We were looking to buy a front loader when I happened open this company with video instructions and positive comments from other people with the same issue. For the cost it was worth a try. Following the video and in less than one hour the washer was back in service. It now operates like the day we installed it new. Highly recommend this fix which should save you hundreds on a new washer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Enrique from Miami Shores, FL
- Parts Used:
- WP21258
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
spin cycle did not activate
Replaced hinge switch. Still no spin cycle. Noticed hinge bearing cracked & if hinge forced into switch, spin activated. Ordered new hinge bearings.Spin cycle still didn't engage. On further examination, observed that hinge was bent. Straightened hinge & worked like a charm. Didn't really need new switch or bearings. NOTE : Avoid having washer door bang shut.Took longer than expected, but each procedure was simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Danny from HARRISBURG, PA
- Parts Used:
- W10404050
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
Washer would not agitate or spin and took over 2 hours to go through all cycles.
Started by replacing the lid latch assembly but this did not fix the problem. Parts Select representative suggested replacing the drive pulley clutch assembly. I order this and a new shift actuator. Had difficulty installing the new black shift actuator as it has a different electrical connection location from the original red part. The plug on the existing wiring harness would not reach the socket on the new black shift actuator. I had to remove the socket from the new black actuator casing so the plug would reach the socket. Washer is now working.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ace from VENICE, FL
- Parts Used:
- W10205824
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
The spin cycle was very noisy & shook the whole machine.
The part we needed wasn’t pictured — nor the quantity identified. There are 4 absorbers required for full replacement. I received one absorber — 3 1/2 inches X 1 1/2 inch wide X 1/8 inch thick. Including shipping, the cost was $53.00!! Outrageous! A 10 foot roll of the same thing can be bought online for less than $20.00.
By the way, it didn’t solve the problem.
Paul
By the way, it didn’t solve the problem.
Paul
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michele from ROCHESTER, NY
- Parts Used:
- W10780048
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
The washer was shaking during the spin cycle
Exactly like the video from the website
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from WARMINSTER, PA
- Parts Used:
- W10404050
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Washer would go into the cycle to rinse dry.
Replacing the part was fairly easy. However it did not resolve the problem. The spin cycle did not activate,leaving my washer full of water. We ordered another Maytag Washer. Hopefully this one doesn't break down for a long time.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harold from Blaine, WA
- Parts Used:
- W10721967
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
Making groaning noise in spin
Having been out of the business for quite a few years I thought that I was dealing with a direct drive machine. Thinking that it was the motor coupler. I removed the control panel and attempted to pull the cabinet froward. Not so, it had a solid cabinet, so I tilted the machine against the wall and looked under the washer finding the driven Transmission pulley loose on the shaft. The splines on the pulley were pretty well worn but I tightened the nut and it worked okay. But I ordered a pulley and replaced after it's arrival. The motor capacitor also broke it's mount off so I had to rehang it with zip ties and repaired the wires to the Capacitor, (Which BTW had about 22 gauge wire). I found it hard to believe that they would use such small wire.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Howard from Boynton Beach, FL
- Parts Used:
- 350930
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Both outside door handles turned very beige
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Diana from Chimacum, WA
- Parts Used:
- W10404050
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
door latch broke
Figuring out how to take the lid off was the hard part. Took out the old and replaced with new and put lid back on and rehooked up.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from DREXEL HILL, PA
- Parts Used:
- W11244231
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
Replace drain hose
At first I had to position the washer so I could get access.. after having it positioned, I figured it out. Getting the clamp fastened, I was done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from Keenesburg, CO
- Parts Used:
- W10404050
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
The lid lock switch on our clothes washer went out
I had to remove 3 screws from the back of the washer to be able to lift the top. Then remove 3 screws under the lid which held the switch in, unplug the old part and put the new one in. It was quite sinple. The most difficult part was figuring out you have to slide the top of the washer forward a bit to be able to tilt it up.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David B from Madison, IN
- Parts Used:
- W10404050, WPW10240513
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Bad latch lock
Took the back of the control panel off, lifted the top of the washing machine up took off nuts holding the latch lock off, installed the new parts put back together. Piece of cake...because i got the right parts the first time. Thank you PartSelect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Lincoln, RI
- Parts Used:
- W10404050
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
would not unlock
Disassembled ,as assembled.
Was this instruction helpful to you?
Thank you for voting!