11021182011 Kenmore Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Larry from HICKORY, NC
- Parts Used:
- WP8536939
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The main knob insert snapped.
Nothing to it. Just remember to put the insert in the knob, NOT on the selector stem. Line up the flat part of the insert with the flat part of the stem and push the knob in place.
Don NOT ram it on the selector stem. When it's seated, don't push any more. That's all there is to it. It works. If the pointer on the knob indicates the selector is lined up correctly, but it isn't, the problem is the selector, not the knob.
Don NOT ram it on the selector stem. When it's seated, don't push any more. That's all there is to it. It works. If the pointer on the knob indicates the selector is lined up correctly, but it isn't, the problem is the selector, not the knob.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Terry from HANCOCK, MD
- Parts Used:
- W10404050
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
washer wasn't spinning on final spin
First I found and reviewed videos on line to do the repair for my machine and when I actually did it the videos made it simple to do. Always look for videos of the installation for your machine or appliance and the job will go easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ernestine from CARRIERE, MS
- Parts Used:
- W10780048
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Making noise when spinning tub hit side of washer.
Remove top of washer suspension
Rod goes on side of tub .
Rod goes on side of tub .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from BAKER, FL
- Parts Used:
- WPW10006384, W10721967
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Loose pulley
Tightened up the pulley as the video showed me that might be the issue.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from GRAIN VALLEY, MO
- Parts Used:
- WPW10006384
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
squeal and chirping while in risne / spin mode
Removed belt cover from bottom of the transmission , remove old belt, clean the pulleys ,and re install new belt. The new belt fits tighter so it did a few time to get the belt fully seated. Re install belt cover.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chet from CLEARWATER, FL
- Parts Used:
- WPW10006384, W10721967
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set, Wrench (Adjustable)
heavy loads did not spin dry properly
I followed the instructions provided by the video which I thought were spot on. Even to the size of the phillips screw driver.
Was this instruction helpful to you?
Thank you for voting!
Agitator directional cogs worn out
Removed bolt holding top of agitator, removed top of agitator. Replaced parts. Reinstalled agitator. An old machine now works like a new model.
Was this instruction helpful to you?
Thank you for voting!
Agitator loose spinning
Three of the four agitator cogs had broken. The agitator was able to spin freely both clockwise encounter clockwise which it should not be doing. I replaced the cogs as well as a couple additional parts just to be sure but the cogs were the important one. Very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Staten Island, NY
- Parts Used:
- WPW10276397
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Socket set
The washer stopped draining.All the pump motor did was hum.
I drained the machine and pulled it away from the wall.Then I disconnected the drain hose and removed the back panel.Next,I removed the three screws holding the pump in place and disconnected the power plug from the motor.I then removed the short drain hose from the pump.Installation was the opposite of the removal sequence,and the machine worked fine right after I was done.The new part was identical the the old one,and the job was a snap.
Was this instruction helpful to you?
Thank you for voting!
Wouldn't agitate
Removed lid panel changed lid lock switch. Took cap off removed 7/16 bolt changed out thrust spacer and agitater repair kit. Took about an hour.
Was this instruction helpful to you?
Thank you for voting!
The Agitator in my washing machine wasn't spinning, and was loose.
After researching and learning from the university of YouTube, I ordered new agitator 'dogs' from PartSelect - the rubbery dogs which look like gummy bears, were worn out in my machine and needed to be replaced. These dogs secure the inner part of the agitator. After watching several videos on YouTube, I knew precisely what to do and what I needed. I researched and found PartSelect on-line and they were very helpful and sending me the dogs. It was a very simple fix, and my washing machine now is working like brand new. Thanks PartSelect for all your help and will reach out again for any future self-fix projects!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JERRY W. from CARROLLTON, GA
- Parts Used:
- W10721967
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
making noise when starting spin cycle
Watch video on the site and the insulation will be easy and take about 30 min.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from LIVONIA, LA
- Parts Used:
- W10404050
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Lid lock not working.
Followed instructions.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fernando from Houston, TX
- Parts Used:
- 285748
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
I noticed that in the spin cycle the machine did not sound like it was suppose to. So I took the time and watched it go thru the steps and saw that it was not spinning.
Went on line and ordered the piece I need. I got my socket set out, held the center piece in place then with the socket unscrewed the bolt. Popped the plastic washer off put the agitator clips in, put the plastic washer on and bolted it back together and was done. Easy as 1, 2, and 3.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Todd from hampstead, NC
- Parts Used:
- 285748
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Did not Agitate, spun freely.
Used screw driver to pop top off to access the bolt on spinning unit.Used socket wrench and took bolt off of bottom of spinniner. Replace agitater with new parts and reassembled. Now it works like new.
Was this instruction helpful to you?
Thank you for voting!