11016986500 Kenmore Washer - Instructions

Removed broken hose and replaced with new hose. My washer will be 21 years old in January.

Half inch extension. Removed plastic set piece. Remove agitator cap. Remove ring remove worn cogs. Replaced new cogs Replace lock ring, back together. 10 minutes

Removed Softner dispenser and cap. With a 3/8" socket wrench and extension And 7/16" socket I took out the screw holding the agitator and removed top section of agitator. Turned upside down and removed the rubber grommet that holds the cogs in place. Replaced cogs and reinstalled grommet. Aligned top part of agitator with 2 tabs and put back in place and secured with 7/16" screw. Replaced cap And dispenser. Good to go. Works perfectly. Very easy repair.

1. Need mop, bucket to catch leftover water in machine before you remove old hose. 2. Removed old hose by removing clamp. 3. Dried up any remaining water around fixture before attaching new hose. 4. Slide clamp to bottom of hose before attaching to machine. 5. Attached hose and clamp to machine where old hose was removed from. Make sure clamp is secure. (Please note that clamp that came with the new hose was too big. I used the old one. Worked perfectly). 6. Finally run a little water in you washer, then run out to test tightness and there is no leaks.

I clean out the fabric softner dispenser on my machine on a regular basis and found the seal split. After looking at several sites to try and find this part, I found this one. Ordering couldn't have been easier and repair only required pulling up the cup for the softner and installing the cap.

Thanks for making finding part so easy . . . .

Removed top cap of agitator and pulled out the inner cap. Spread a pair of needle nose pliers and placed them in square holes on each side of nylon fitting. Unscrewed nylon fitting and removed top half of agitator. Replaced directional cogs/dog ears and put agitater back together. Works like new. Easy fix.

PS Received parts in 72 hours. $10.00 bucks and never left the house.

First I removed the old hose to ensure I ordered the correct part. When I got home from work the part had arrived by us mail. I opened the box and installed it without any modifications and within 5 mins. I hooked up the washing machine to the hot and cold water, then the drain hose. I was washing cloths within 20 mins of opening the box!

It was easy, take off the cap, then loosen the nut. Take it apart, change the dog ears, put back together. It was done.

After flipping the washer on it's side snap off the clips that hold the motor in place and discard the old coupling. The new coupling fits in very snug some may need a little persuation to attach but once attached the motor lines up nicely and just snap back the clips, turn the washer over and test with a fresh load.

Inserted new drain hose thru back and snapped into place. Tipped washing machine back, clamped new hose with pliers.

Hello the installation was real simple I first uplug machine from wall I turn off all water leading to in to the machine I then tip machine on it side I then took loose all wiring leading to the motor then motor is held up with 3 screws and 2 bands that hold it in place I reinstall the new motor coupling insert the wires and turn back on the water leading to machine then plug machine back in, every thing was good to go. . . . Save a lot of money doing it my self so simple to do. . . .

First, disconnect from power & turning off the water. Then, accessed the part by tipping the unit back enough to work. Remove the hoses by loosening the spring clamps. Here is where things got a bit sticky. The pump motor shaft had corroded enough to make removal of the pump a wrestling match of sub-WWF levels. Once forced off, additional time was spent removing corrosion from the shaft to facilitate fitting the new unit. A little lube was used here. Re-assembly was quick & washer was righted, plugged in and returned to service. It is a simple repair which can, with a little acting ability, be portrayed as a monumental task requiring super-human strength & the wisdom of Solomon. I played the part well enough to merit a huckleberry pie for my effort & sacrifice! Thanks!

After the wife held the phone to the washer so I could hear the horrendous noise it was making. And I screaming at her "shut it off, shut it off!' I came home and took the agitator apart, and found the directional dogs worn out. Went to the computer and easily ordered new parts, which came very quickly. I took off the agitator with a long extension and socket, put in the new dogs and reversed for installation. Told the wife get back to doing the laundry!

Raised washer on cinder blocks high enough to get underneath, removed wiring, capacitor (because it got in the way), removed spring clips from pump, removed pump, no water spillage this way. removed clips from motor, removed motor, pulled old broken coupling rubber ring and plastic pieces out, used a spark plug driver to press new ones in place on the gear shaft and motor as they will fit tighter because they have a metal reinforcement that the original did not have, lined up the two halfs and clipped motor back on, cliped pump back on, reconnected wires again, lowered off the blocks and washed a couple loads that night.

I used pliers to loosen the hose clamps and the small springs that hold the water pump to the water pump motor. The old pump then came off by simply pulling it off. The new was was the reverse. Everything worked well.
The biggest problem had been finding that the water pump was leaking. I first tried to fix it with epoxy but it is apparentlly made of nylon and the expoxy didn't stick well.
I am still annoyed that Whirlpool makes a water pum that leads so soon. The Whirlpool site showed my model number as non existent. Later, after purchasing the right one from this third party site, Whirlpool sent email that they found the model number and gave me a much higher replacement price for the pump.