Models > 11049962603 > Instructions

11049962603 Kenmore Washer - Instructions

Jump to:

All Instructions for the 11049962603

Customer:: Wanda from PIKEVILLE, KY
Parts Used:: WP8182862
Difficulty Level:: Very Easy
Total Repair Time:: Less than 15 mins
Tools:: Pliers, Screw drivers

Tub was filling with water while washer was not in use

Shut off water supply, unplug washer. Remove screws on fir the top of washer, remove supply lines for water, lift top of washer off, unclip wires going into outlet value, reclip wires into new part, put parts back into place, secure lid and hoses, turned water supple back on plug in washer and put washer back into place, there you go. Oh, one more thing, make sure you check for leaks prior to hut washer back into place. Easy as pie

5 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: Robert from PALM BCH GDNS, FL
Parts Used:: WP8182862
Difficulty Level:: Really Easy
Total Repair Time:: 30 - 60 mins
Tools:: Nutdriver, Pliers

Water leaking into drum when machine shut off

Shut off water. Unplug electric. Remove top panel. Unhook hoses. Unhook tubing unplug solenoid. Use torx to remove part. Reverse steps to install new part. Replace top panel. Hook up water & electric.

5 of 6 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: LAURA from SPARTA, KY
Parts Used:: 280187
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Pliers, Screw drivers

washer not drain or spin

it was a really easy fix. unclamped the 2 hoses and took out screw, removed water pump. Connected two hoses back and set in place then screwed in locking screw. could not have been any easier.

6 of 10 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: Gustavo from YOUNGSTOWN, OH
Parts Used:: WP8183202
Difficulty Level:: Very Easy
Total Repair Time:: 15 - 30 mins

Door was not closing properly, broken swivel arm under hinge.

removed door from washer, set flat on table and just loosen up the screws all around, removed old hinge and replaced with new hinge, very easy. back to washing clothes.

4 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: Donald from PALESTINE, IL
Parts Used:: WP8182862
Difficulty Level:: Very Easy
Total Repair Time:: Less than 15 mins
Tools:: Socket set

Whirlpool front load washer drum filling with water after use.

Followed the installation video instructions. Removed the washer top with a 1/4” nut driver torx bit. Shut off and unhooked the water lines to the washer. Took one screw off of the solenoid valve on the washer back. Removed the water line on the solenoid on the inside with a pair of pliers. Installed the new solenoid in reverse order. It took maybe 10 minutes to take off and replace. Very easy to do.

4 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: Martin from Kotzebue, AK
Parts Used:: 280187
Difficulty Level:: Easy
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers

Pump not draining the water out.

First I made sure the washer was unplugged from the outlet and I took out 3 screws that held the front panel and removed it to get access to the pump.
I disconnected the electrical plug to the pump and there were 3 phillips head screws that held the pump in place that needed to removed. Pulled out the old pump and slide the new one in it's place with no prorblems. Tighten the 3 screws on and plugged it back in and away we went washing clothes again.

4 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: JOHN from OMAHA, NE
Parts Used:: WPW10467168, 280187
Difficulty Level:: Easy
Total Repair Time:: 15 - 30 mins
Tools:: Pliers, Screw drivers

PUMP HOUSING LEAKS

REMOVE AND REPLACE. FLEXIBLE RUBBER CONNECTOR WAS NOT A EXACT REPLACEMENT, THE ORIGANIL HAD A BACK STOP VALVE, NOT SURE OF THE EFFICATE ON MACHINE.

5 of 8 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: Gopaul from Queens, NY
Parts Used:: WP8182119
Difficulty Level:: Easy
Total Repair Time:: 30 - 60 mins
Tools:: Nutdriver, Screw drivers

Bellow was damaged,water leakage.

First,we took apart the front of the washer and then we removed the old bellow and put the new one on.After we put back up the front of the washer and open the door to put the clamp on then after we unlocked it.After it was working good as new.

5 of 8 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: Christopher from MORGAN HILL, CA
Parts Used:: W10902779, WP8182210, WP8182119
Difficulty Level:: A Bit Difficult
Total Repair Time:: More than 2 hours
Tools:: Nutdriver, Socket set

Torn bellow lip

Replace bellow with help from Youtube video.

4 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: Paul from TARPON SPGS, FL
Parts Used:: W10822553
Difficulty Level:: Really Easy
Total Repair Time:: 30 - 60 mins
Tools:: Screw drivers, Wrench (Adjustable)

Spring balanced tub violent shake on spin

Washer was on a 13 inch high platform I built for front.load Heat washer and dryer. Removed 3.screws from bottom of front panel and had access to all 4 shocks..front and rear. All shocks were unattachedeither at base or on tub. Easy to install all 3 from front without moving Mach. I figured if 1 or 2 shocks failed the violent.movement broke the other 2. Purrs like.a.kitten now. No bearing.or spring.damage.

4 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: anthony from EASTPOINTE, MI
Parts Used:: WPW10003250
Difficulty Level:: Very Easy
Total Repair Time:: 30 - 60 mins
Tools:: Pliers, Screw drivers

I was getting a sewer smell when the washer drained I did every cleaning technique and didn't solve the problem then I cleaned the inside drain hose and that helped so I replaced the hose and problem solved.

I removed the back panel to access the top end of the hose then I removed the lower front panel to access the lower end of the hose that attaches to the pump. The hose is secured with spring clamps and they were removed with pliers, the panels are secured with screws.

I replaced the hose and reinstalled the panels and I was done.

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: Lindsey from STEWART MANOR, NY
Parts Used:: WP8183202
Difficulty Level:: Very Easy
Total Repair Time:: 30 - 60 mins

Hinge broke

We read your you tube instruction and followed the video

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: Gerald from Douglas, AL
Parts Used:: WP8182119
Difficulty Level:: Easy
Total Repair Time:: 30 - 60 mins
Tools:: Screw drivers

Replace Bellows between door and tub

Remove top and front
Care taken to unplug door wiring
should have taken notes or photos where srews go and order
remove old bellows large hose clamp and sping tensioned clip
clean surfaces
install new bellows on tub only
put all panels and door together
Connecting wiring to door and strain relief takes 2 people
connect bellows to door with spring clip

5 of 9 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: Darrell from Lady Lake, FL
Parts Used:: 280187
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

Pump not working

Replaced pump

4 of 6 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: Francisco from DELTONA, FL
Parts Used:: WP8182862
Difficulty Level:: Very Easy
Total Repair Time:: 15 - 30 mins
Tools:: Pliers, Screw drivers

Tub filling when power was off due to inlet valve leak.

Followed instructions as shown on repair video at site.

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

All Instructions for the 11049962603