11047512603 Kenmore Washer - Instructions

Took of the panel, unscrewed the old drain, screwed the new drain in. Very very simple to do! The first part I received leaked, I called customer service and they gave me a refund and express shipped a new part - no questions asked. Very good customer service!

unplug washer from outlet carefully tilt back to get at underside of washer remove bottom panel. pump location lower right front. remove two hoses from back using pliers keep note on hose location. remove two bolts on underside of machine slide pump to the right to release from rubber holders to install reverse the process also good idea to use the new hose clamps that come with your new pump and the rubber mounts if they are included

very easy to take off the bad belt and easy to put the other on. skill level would be a low anyone with a socet rench and a screw driver can replace the drive belt. shipping was extremly fast. 3-6 day shipping was there in 2 days.

Replace water pump

Unplug Unit, remove lower cover screws with screwdriver that has 1/4 drive at end, put 2 gallon bucket at strainer remove water. Remove inlet hose clamp and outlet hose clamp, disconnect pump motor wiring plug, aggressive push to RIGHT popped right out. put a dab of Vaseline on new units rubber base slide back in reverse order. Plugged in check for leaks put back together, Repair took less than 15 minutes, working great! WHAT I FOUND IN STRAINER: LEGO'S-CHANGE-PAPER CLIPS, enough things to destroy the impeller !

took the old part out by the front panel and put the new pump in and now it works great. only took a couple of minute to put the new one in. thank you for saving my washer.

We purchased a new pump and installed it very easily. My washer works great!

I used the video at parts select as a review, then just followed it. Easy de-install, reminder there's water in the line be prepared with a pot or vase to hold the water. Easy install. Washer runs perfect now. As quiet as when we bought it. I always try to fix before I re-buy, not a big green guy but I try to keep stuff working and out of land fills. Also the part was at my door in 1 day, Awsome!.

After unplugging the washer, the unit was pulled forward and tipped backwards, I placed a 2x4 under the washer to serve as a brace. I removed the existing bolts holding the old pump in place, removed the spring hose clams, unplugged the pump and removed the damaged part. inserted the new drain pump, re-inserted the bolts and tightened them, replaced the spring clamps with "regular" hose clamps supplied with the replacement part, plugged in the power supply, removed the brace, pushed back the unit and plugged it into the outlet. From start to finish - about 20 minutes. Was running wash about a half hour after I started.

I was already very familiar with the motor & drain pump, as I had disassembled my original one in attempt to find the problem & fix it. Finally, I broke down & purchased a new one. It was VERY easy to install! The most difficulty was finding the right sized board to put underneath & raise the machine up (with the dryer attached to the top of it) to place the board underneath so that I could tighten the bolts from underneath to attach the pump. After that was over, the rest was cake! Just attach the hoses & the electrical, which just clips in place & my washer is like new again! Yay! Oh, and yes, I'm a woman DIY'er.

Just use the video. Shows you all you need to know. Very easy. Do it yourself and it saves you money.

I watched the video and it really was as easy as it looks. Great shipping time, I ordered the pump Monday and it arrived on Thursday, standard ground shipping!

My dryer is on top my washer so I removed the dryer and pulled the washer out. I had to get rid of the water that was inside so I used my wet vacuum on the drain hose and sucked it out I then removed the front cover and the I tipped it back and removed two screws from the bottom of the pump bracket underneath the washer and moved the two clams on the pump hoses back to uncouple the hoses. I removed the pump and installed the new one and hocked everything back including the wires to the pump which is just a quick connect and pushed it back into place and it worked like new

Followed instructions from a You Tube video. I'd recently lost my job and money is tight and I thought we could save money doing it myself. By watching the video and ordering parts from you we were able to save $500 between parts and labor. Thanks

the hardest part of the repair is having the confidence to pull all the screws and remove door etc. Dish soap was a good trick when I needed the last bit of the bellow to pop/stretch into place in step 1 of attaching the bellow.