11047511702 Kenmore Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- kevin from elizabethton, TN
- Parts Used:
- WPW10730972
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
Washer washed cloths then would not rinse
Just went by instructions provided by parts web site
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter from Naples, FL
- Parts Used:
- WPW10730972
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
My washer was not draining
It was real easy. I disconnected the wiring as shown in the video. I took the clamps off the drain pump , once off I slid the old drain pump off. I slid the new pump on , attached the hoses with the clamp provided and connected the wiring. Just follow the video and you will find it to be very easy! Thanks Parts Select for saving me money
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Antonio from La Puente, CA
- Parts Used:
- WPW10730972
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
My washer would not drain, weird noises, etc.
This part worked great! Completely fixed all the problems that I had with my washer. A bit hard to actually place it in(pliers are necessary) but otherwise very easy to install.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeffrey from Saugus, CA
- Parts Used:
- W11366249
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Water on the floor under washer
I pulled the front load washer away from the wall and unplugged. I tilted it back against the wall. I removed three screws from the lower front cover plate of washer. Once removed, I had access to the tub to pump hose which I found a small hole in. I went online to Partselect and found my part. The hose was connected in three different places by compression clamps. I then pulled the compression clamps off the connections. Cleaned up all connection points with a damp rag. Upon installation of the new tub to pump hose, I discarded the compression clamps and installed the new part using radiator clamps purchased at a auto parts store. Plugged washer back in and started a load too make sure all connections were good and tight with no leaks. After checking for leaks, I re-installed the front cover plate. Tilted washer back down being careful not too set it down hard or on my feet. Job Done....
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Todd from Cherry Valley, IL
- Parts Used:
- WPW10730972
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
No drain fault code F-21
Very --simple remove front acess panel -- open sump clean out remove water out of existing pump an hoses with small wet dry vac -- remove small wire harnes --cut band clamp on discharge with side cutter --remove inlet -suction side of pump hose clamp with channel locks --un bolt two screws on bottom side of washer with 5/16 nut runner --discard old pump reinstall new one in reverse order --only takes about 20 mins total !!! ---
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tina from Denver, PA
- Parts Used:
- WPW10730972
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers, Wrench set
needed to replace water pump
dryer stacked on top of washer. had to lift washer and block w/2 x 4 to get under unit and replace pump
Was this instruction helpful to you?
Thank you for voting!