11081476630 Kenmore Washer - Instructions

My dryer is 35 years old and thought this was it, but I googled the question and found out it was the door switch. Orderd the part and received it very fast and didn't want to wait for my husband to come home so I went on you tube and found a video how to open dryer and change switch. I did it in about 30 min. and yes it is now perfect again. No problems. I just unscrewed the old switch and put the new one in. Maybe I'll get another 35 years out of this machine. :o) Thanks for making it so easy.

replaced missing screw and pad and now machine works perfectly

Two screws holding top, unhook wire conector. remove cabinet,replace switch. Reassemble.

Order the part and put the new part on and put the washing machine cabinet back on and check the washer for the water filled up and then it's starting to go on the spin cycles.

1- Remove power connection, remove water connections. 2- Remove the top controller box and free it from its hinges. 3- Loosen the back cover to get access to water valve assembly. 4- Remove hose clamp connected to inlet water valve. 5- Remove the old water valve which is secured with 1/4" screw. 5- For installation perform step 5 to 1 and then test your Installation.

Replaced lid switch, but problem still continued.

Unplugged the power while the washer was running, and the water kept on running. The water inlet valve was stuck open. I removed the inlet valve and you cold blow air thru it, it should be closed with no power applied.Ordered replacement from this site it was a perfect fit. As far as the removal and installation procedure, just follow the video as presented on this site. Good Look.

laid washer on it's side and changed hose

Installed long end first and snapped it into place.

This should have been done under 30 minutes but when you don't have a repair manual, you have to do some guessing. I have to remove the back panel. On only thing that was hard was unspringing the two flat springs. After I got the panel off, the rest was easy and the dripping stopped. Oh, there is a screen where the hose connects to the inlet valve. If you can clean the screen often, you can continue to get a good water flow.

Removed two clips on back panel holding control panel.Removed end plates on control panel. removed two front screws holding control panel. removed wiring harnesses noting location. Set control panel aside. Removed two large clips holding rear panel to washer cabinet. Pulled washer cabinet from the front away from the rear panel and tube. Removed two screws holding water inlet valve. Removed water inlet hose from inlet valve using channel lock pliers. Installed new water inlet valve using supplied mounting bracket. Reassembled washer in reverse order.

I had to call in to find the correct part because the online recommended part looked very different, and the one found using the model number had no photo, so I was VERY leary of ordering. The service rep said that Kenmore products did not always show up correctly and he gave me the part number needed and there was a photo. The part was not exactly the same, but looked very similar and it was more than 50% less than the original recommended part and part with no photo. I thought that the problem finding Kenmore parts was odd since Kenmore is like number one, right? Part took 3 days to arrive, which I thought was great. Turned off power and water. Removed water hoses. Removed three screws from the back of the top (front loader). Removed the top. Removed a screw holding on the water inlet valve from the outside of the unit through the back cover which required a star driver. Unattached the 4 electrical leads. Unattached the outlet water hose (held on with a squeeze type metal clamp -not sure of the exact name for these). The problem that I had was that the water outlet hose bib attachment was slightly larger than the old one, so the hose would go back on, but the clamp was too small so I cusses a lot before figuring out the problem. I had to go and purchase a new larger clamp. After that, I simply attached the electrical connections and put the outlet back on. One other small problem was that the place where the screw through the back cover was originally attached no longer lined up with the new valve. The plastic piece was shorter than the old one so the screw hole did not line up with the hole in the back panel. The screw isn't really necessary. Overall, replacing the part was easy and I was pleased with the process.

Ordered the correct part, watched a YouTube video.

Turn off water, unplug machine
Disconnect water lines to the valve
Unscrewed the clear plastic tabs on the top of the machine, then pryed the back away from the top white part.
Two gold clips can be popped out with a long flat head screw driver.
Pulled the back away from the machine enough to disconnect the wires from the valve. Unscrew the screw(s) from the valves.
Old valves out, new valves in. Plug in the wires, screw in the screws.
Then, to get the gold tabs back in place.....i called NASA.
just kidding. They're tough!
I slipped one into the back and held it in place with my thumb. Then I lined the piece up with the slot inside the machine. Then, i pryed the top white part away as I pushed them together. Stuck a long handle screwdriver down in and pushed REALLY hard on the gold tab to get it to snap into place. Everything is really tight, so you might have to try it a few times.....i left some blood behind.
repeat for the other side, snap in the clear tabs, hook up the water lines, plugged it in......
Then I sat back and listened to my wife praise me for fixing her machine!

I just followed the instructions found on this website. It covered everything you need to know. I have just one thing to add though. Look over everything first and formulate a game plan. Keep all screws etc. and put them in a plastic bag so you don't lose them. You might try using a heavy hammer to force the clips holding the back panel to the top of the machine back in place. One more thing; use a piece of wood to set the back panel on while you replace the intake valve.