11084090830 Kenmore Washer - Instructions

Just took screws on top panel holding the gauges pop the spring like braces holding the body of machine to back panel removed water valve one screw unhooked wireing than replaced new valve in reverse order.

Your video was helpful. I just followed the directions, replaced the valve, put it back together and celebrated spending $28 instead of the $100 deductible on my home warranty. If you're sure of the part you need, just do it.

Shut off the hot water supply (pretty sharp eh?). Disconnected the hose from the hw supply and the at the connection to the washing machine. These had not been touched in at least 15 years and were somewhat tough to loosen but finally came ..... accessibility was a problem for the connection to the water supply as it was in a recessed wall box. Fortunately, we had some washers for the hose connections so the install was a snap. Hardest part of the whole job was moving the washing machine out from between the drier and the wash tub .... tight fit. Thanks for the quick service and to FED EX for their delivery. The delivery fellow was a real gentleman.

took off the rear panel and removed the existing inlet valve and installed the new one. Replaced the rear panel and the machine work better than ever.

turn off hot and cold water faucets,unplug the power,pull washer out to gain access to rear cover, remove the top control panel screws,push back and lift off, disconnect hot and cold water hoses from inlet valve and remove enough screws from the back panel to remove the valve, disconnect the valve from the tub fill hose (mine had a spring type hose clamp) note the orientataion of the hot and cold hoses and the solenoid connectors for the hot and cold sides,(mine is stamped in the rear cover)reconnect and reassemble in reverse order and check for proper operation.

took part top of washer saw switch replaced it not to difficult it is always easier when you have new one to look at

First, I unplugged it and disconnected the water hoses (the water has been off to it for days). Then, I tried taking off the back of the washing machine. This didn't work, and I actually ended up googling instructions and found pretty detailed, illustrated instructions at Popular Mechanics.
You need to unscrew the front panel that contains all of the controls first, flip it up, and unhook it from the back of the washer (via an electronics clip and 2 metal clips). The outer cover can then be taken off. I recommend undoing the internal hose next -- I used adjustable pliers to squeeze the connecter and loosen the hose. Then, unscrew the water inlet valve and take it off.

Putting everything back together literally just means reversing the instructions.

My washing machine is on a raise service, and I still haven't gotten the outer frame completely back in place correctly, but it's not touching anything or creating any problems. It's really only to safeguard parts anyways, so no worries if it's not perfect -- at least it works now!

Removed the hoses from the inlet valve. Removed screws that hold control panel in place . Removed control panel which exposed two clips that hold the top of the back panel. Removed the ground screw freeing the ground wire, removed the plastic loom which holds a bundle of wires. I next removed the plastic plate that protects the fill valve from splashed water. Removed the screw that holds the valve in place, then removed the wires and the fill hose. Reversed steps to put back together.

First I turned off the water to the washer and then removed the hot/cold water hoses going to the washer, unscrewed the water hoses from the washer, and cleaned the wire screens located immediately inside the inlet water valve. This did not solve the problem. Second, I loosened the hex head screws on the back panel of the washer. This allowed me access to the valve. I tested the valve solenoids with my ohm/volt meter and all checked out OK (but this did not make sense). Third, I surfed the web to find out if the symtoms of the washer's problem were the same as experienced by other people. I found several reports of the same symptoms, all which were solved by replacing the water inlet valve. This conformed my original diagnosis although the valve tested as OK. Fourth, I ordered the part from PartSelect, and removed the hose clamp and two mounting screws holding the old valve to the back panel of the washer and removed the old valves. Last, when the new valve arrived, I assembled the new backing plate to the new valve, attached it to the washer's back panel, attached the water hoses to the valve after fitting new rubber seals to the inside of the hoses, and reattached the washer back panel. The washer is working perfectly again.

removed the two screw that hold the inlet valve take hose of .the first was takeing the back of than the hoses from back hose on bottom of machine.

I own a small, local handyman service as a Father/Son team. This repair is PERFECT for an apprentice to do as a confidence biulder. He learned the safe way to service a machine with garanteed success. This is a job anyone with basic knowledge can easily do with a little on-line homework on their machine. -Jim & Tom W.-

This was a thirty year old Kenmore washer. I removed the control frame, and then removed the two nuts holding the water inlet valve. The valve itself was easy, two water lines and one fill line. Reassembly was problematic as this valve was not exactly the same, I just tied off the valve to the water lines so it would not move.
Of course what took the most time was a run to Home Depot as the hot and cold water hoses were old and I replaced them with new.

First I unplugged the washing machine and turned off the inlet water faucets. I prepared my tools, spead a drop cloth, and had ready a towel and small bucket to catch water from the hoses.
I pulled the washer away from the wall and removed the screw holding the ground wire. I disconnected the inlet hoses and the drain hose from the wall and put the loose ends in the washer tub. Then I completly turned the washer around for easy access. I removed the inlet hoses and the drain hose using the bucket to catch the little water that was still in the hoses. I removed 2 screws holding the top control panel to the back place and removed the 3 screws at the bottom of the back plate. I also removed the two screws holding the control panel to the top of the washer. The water inlet valve is located on the left side looking at the rear about half way up. I was able to move the left panel of the washer out of the way an inch or so, and pull the left side of the rear panel away a few inches so I could stick my hand in and unhook the cold and hot wire cables. I memorized which went into which slot. Then I unscrewed the water inlet valve and pulled it out the opening to the back and using a pair of pliers I loosed the water clamp and removed the rubber inlet hose. A small amount of water came out which I was able to catch in my small pail.
The water inlet valve comes with a separate mounting plate. I attached the mounting plate with one of the screws provided. The screws are identical except one has a flat slot and the other has a special star slot.
I reattached the rubber inlet hose using the pliers to hold the clamp then positioned the water inlet valve back in place on the back panel. I put a screw in to hold it and reattached the wires for the hot and cold control. Then I tightened the screws.

I repositioned the panels and put the lower screws holding the back panel to the washer back in loosely. I positioned the control panel back on the top of the washer and reattached the two screws on the back and then the two screws holding the front of the control panel to the top of the washer. Then I reattached the inlet hoses and draine hose.
I used this opportunity with the washer away from the wall to clean the floor and wall behind it. After cleaning under the washer, I moved the dryer over and cleaned under the dryer and made sure the dryer hose was still connected.
I put the dryer back, and repositioined the washer half way back into the opening. The I reattached the ground wire to the back of the dryer and attached the hoses to the wall. Then I pushed the washer back into place. Using a level I rechecked the level of the washer. I turned the water back on and ran a small load of wash to test. It worked fine.

Unplugged the washer and pulled out from wall as far as hoses would permit. Removed and drained both supply hoses. Removed drain hose and drained. Any water left in the tub will drain here so it's best to make sure it's drained prior to repair. Used pliers to hold the hose clamp and removed. Took screws out of drain hose interface plate and pulled out far enough to disconnect it from the internal hose.
Removed the two front screws of the control console. removed the two top hinge screws on the back. Removed four screws at the bottom of the rear access panel. Had to lift unclip several clamps holding the level hose in the control console and a cable connector. Unclipped various clips in the back panel to free it from wire bundle and such. Lifted the back panel up off of the clips located at the rear base of the control panel.

Removed two screws to free the solenoid assembly from the back panel. Unplugged the connectors to the original solenoid assembly. Disconnected the internal hose from it. Installed screw and plate supplied with the replacement solenoid to configure it with the same orientation as the original. Connected the internal hose and electrical connectors. Reassembled the back in reverse order as diassembled.

Had no problem in disassembling the unit to get to the water inlet valve area. Very little problem installling the inlet valve but had somewhat of a difficult time getting the housing reassembled. There is a good flow of both hot and cold water which has cut down on the fill up time and washing time. Glad it is still working after 15 years. Instructions on the internet were extremely helpful. The delivery time of part was amazingly fast.