Models > 110359054

110359054 Kenmore Washer

Jump to:

Find Part by Name

Keep searches simple, eg. "belt" or "pump".
Keep searches simple, eg. "belt" or "pump".
Spin Pinion Seal – Part Number: WP356427
$11.14
This seal is for the top of basket drive tube shaft.
In Stock
Order within the next 6 hrs and your part ships today!
SEAL-SHAFT – Part Number: WP91939
$8.00
Transmission shaft seal.
In Stock
Order within the next 6 hrs and your part ships today!
V-Style Cogged Tooth Pump Belt – Part Number: WP95405
$25.68
In Stock
Order within the next 6 hrs and your part ships today!
RING-WIRE – Part Number: W11033823
$7.43
This is part of the Basket Drive and found under the Brake Lining parts.
In Stock
Order within the next 6 hrs and your part ships today!
Wig Wag Solenoid – Part Number: 84867
This transmission shifting coil set has 2 solenoids - one turns to start the agitating during the wash cycle and the other turns on to start the spin-dry cycle. Only one solenoid is operating at one time.
No Longer Available
Wig Wag Plunger Kit – Part Number: 350384
This wig wag plunger kit comes with a plunger, a cam bar guide, a rivet, and a speed nut.
No Longer Available
BEARING – Part Number: 285205
$7.59
Special Order
SPACER, DRIVE TUBE – Part Number: 356937
No Longer Available
Ring, Retaining – Part Number: 90369
No Longer Available
BEARING – Part Number: 350920
$11.71
Special Order
SPRING – Part Number: 285672
CONTAINS ONE EACH: 92814 SEAL
No Longer Available
GASKET – Part Number: 95089
BULK OF 50 PCS.
No Longer Available
View More

Questions and Answers

Be the first to ask our experts a question about this part!

Common Problems and Symptoms for 110359054

Viewing 3 of 3
Leaking
Fixed by these parts
Fixing Fixing
How to fix it
Burning smell
Fixed by these parts
Fixing
How to fix it
Will not drain
Fixed by these parts
Fixing
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Richard from Newark, DE
Parts Used:
84867
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers
Washer would not spin on any cycle. The pump still work so it was not the belt.
The wig wag selenoid was not shifting the transmission to the spin mode. Using a 5/16 nut driver remove the two screws holding the back access panel. Using the same driver remove the set screw holding the wig wag onto the shaft. Lift the part off the shaft. If it is hard, using a small pry bar. Install new part and reverse the process .
Read less
34 of 44 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Mike from Roeland Park, KS
Parts Used:
350384
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Socket set
Wouldn't go out of spin brake mode
Used Liquid Wrench to loosen wig-wag solenoid bracket. Drilled out rivet on defective wig-wag plunger. Installed new one with easy-to-install rivet clip. Now works like a charm.
5 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
eric from moreno valley, CA
Parts Used:
84867
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Socket set
replaced wigwag solenoid: washer spun and drained but did not agitate
pulled leads off old wigwag solenoid, removed set screw and sprayed shaft w/wd40 then tapped it off shaft w/small hammer and large screwdriver. put new wigwag solenoid onto shaft then tapped it down into place and tapped it to rotate to expose set screw hole. reattached set screw, reattached leads to solenoid, checked looseness/freeness o f cam arms and it worked
Read less
Was this instruction helpful to you?
Thank you for voting!
View More