11084070820 Kenmore Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Michael from Irons, MI
- Parts Used:
- WPW10254672
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
No faucet adapter
I unsrew the faucet head, and attached th e adapter
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Cameron, NC
- Parts Used:
- WPW10254672
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
changed out kitchen sink faucet set
replaced the faucet adapter I did not save when I change out the kitchen sink faucet set
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Becky from Stanley, NC
- Parts Used:
- WPW10254672
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench (Adjustable)
The Faucet Adapter was worn out.
Ordered a new Faucet Adapter! Simple
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Norm from Hamilton Square, NJ
- Parts Used:
- WPW10254672
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
A gift portable dishwasher did not have the faucet adapter.
Found the adapter on Parts select through a google search. Unscrewed the existing faucet aerator and srewed in the adapter. The plastic shrink wrap holds the washer and screen in place, so don't open it until you're ready to install. Finger snug does it, only use the pliers to remover the old aerator from the faucet. Normally, I don't use pliers, but both of these parts were round and had vertical serrations to engare the plier teeth.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ed from North East, MD
- Parts Used:
- WPW10254672
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Faucet adapter leaked
Replaced the faucet adapter, works fine
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Willie from Virginia Beach, VA
- Parts Used:
- W10820036
- Difficulty Level:
- Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Socket set
Switch broken
I was impressed with the fast time the part was delivered. The price was good too. The installation video and instructions did not match my dryer but it was helpful to some extent. The video and instructions being different was not ya'll's fault because of the age of the dryer. It took me so long to change the switch was because of the location and design of the switch. I got it though.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Colleen from Indianapolis, IN
- Parts Used:
- W10820036
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Socket set
Washer quit running when lid was closed
This repair took me longer because I was just giving it a try - I have no experience, although I tend to be "handy." I'm sure anyone with experience would rate this as "easy" and have taken only a short time. I had to watch the video several times to understand what to do - and the comments were helpful too. My washer is an OLD maytag, so I removed the front of the dash and pulled it forward to access the electronics. My switch had only 2 prongs, so I hooked up to the "lid closed" option on the new switch. It works perfectly now. Very pleased I gave it a try.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruce from Yankton, SD
- Parts Used:
- W10814296
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Socket set
Had issues with removing the inner tub
Had a lot of corrosion on the shaft area and had a hard time removing the inner tub but after some WD-40 and unprintable words and labor it popped off. Cleaned everything up, shaft, inner drum and outer drum. After that everything was a piece of cake. Thanks for the help!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kim from Oviedo, FL
- Parts Used:
- WP21258
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Missing lid hinge bearing
1) Using a Phillips head screwdriver, the two screws retaining the hinge pin to the lid were removed. 2) Remove hinge pin and tilt lid slightly to gain access to bushing hole. 3)Install new bushing in hole. 4)Reposition lid. Insert hinge pin through lid and into bushing. 5)Reinstall hinge pin retaining screws and tighten.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tomas from Orlando, FL, FL
- Parts Used:
- W10820036
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
broken
Removed the old one installed the new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- sean from easthampton, MA
- Parts Used:
- W10820036
- Difficulty Level:
- Easy
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Screw drivers
dryer wouldn't start
I found on youtube that there are directions to repair. Dryer problems are usually one of three things, the door switch being one of them. i checked this last (should have been first). ordered the part( about 65% off sear's cost) and it came in one day! It went on really easy as long as you knew from repair video how to access inside. almost spent $400.00 on a new one.
Was this instruction helpful to you?
Thank you for voting!