11081167210 Kenmore Washer - Instructions

Disconnect power & water then drain hoses.
We flipped the washer on it's side to gain access to the bottom. There was no need to take off the back panel. Keep a 5 gallon bucket and a few rags handy for the extra water in the pump line.
Disconnected the wiring harness. Removed the brackets holding the motor. It's a little tight on the back bracket. It has a 1/4" hex nut on the back side, so I used a 1/4" drive socket (see: small). Removed the bolts holding the gear case (this makes it a lot easier). Disconnected the pump hose and rotated the motor & gear box and pulled forward. This gives you access to the coupling. Remove the broken part. Clean the area for debris. NOTE: each part of the coupling has 3 fingers (these are what breaks off), so check to make sure you get all broken parts. Insert the new coupling. It has 3 parts; the plastic fittings go on tight and need to be snug to the shaft. Use a screwdriver handle on the center and tap down with a small hammer. Spray silicone on the rubber coupler to allow a little better slide.
Reverse the process. Line the gear box and motor up and push back into the tub assembly. We used 2 people to do this. It's easier to have someone stand over it and hold / rotate the gear box while the other one can align the motor & bolt everything back on.
It took us an hour, however, if you were doing a couple you could get it down to 30 min. flat.
Go wash your clothes!

Yes, I agree that the actual replacement of the pump was an easy task on this whirlpool washing machine, however, unlike other posters, I had no access through the bottom of the machine. My machine has a solid pan on the bottom. It has a large hole in the center - I think to access the transmission, but no access where the pump is.
So, I had to dismantle the entire enclosure, first the back (about 6 screws, a couple of electrical connections, etc.), then remove the rest of the enclosure to reveal the guts of the machine. I also had to disconnect a small vacuum tube attached to the tub, and remove the control console on top along with the back. It was pretty straight forward, took about two hours to dismantle. Then, the actual removal of the pump was as easy as others have described here - two spring clips and a hose clamp and I had it in my hand. I ordered the new part, which came very quickly - 2 days I think. Then I took another two hours to re-assemble the machine. It works - yeah!
Symptoms - water leak on the floor, it was actually intermittent for a time, so I procrastinated. Then when I actually did the work, I could see the rust trail and follow it to the leaky pump. The pump was actually leaking through the center, where the drive shaft from the motor goes. There is probably a seal between the impeller and the central drive slot that gives out after a while.
New pump in - machine back together - no leaks.

Repair went well and relatively easy, but did not fix the problem.
Suspect timer switch was the culprit. Nothing was clogged or plugged
up. Water pump and impeller were free and clear with no damage
or leaks.

removed water lines from back of washer. tilted washer to get access to the pump/ removed 2 hoses at pump and removed to snap clips attaching the pump. easiest repair i ever did. washer works fine now.

I am an old woman who is disabled and without any tools or knowledge, but sheer stubbornness and will power, I waited for my tools and other parts to come in, in the mean time I fixed my young neighbors whirlpool washer, well We took top off the nut I had already pre assembled her cam so set it in place of old one put bolt back in place and the top of agitator she says works perfectly now, my parts came in I had nothing to remove as my handicap daughter had already thrown away all the loose parts, I threw away old top agitator, assembled cam and put in place still did not feel tight enough so added seal from other nut!! it worked tight enough, put the inner part back in with new part and soap put the top back on and now works good as new, was disappointed could not put bottom agitator in place, just not strong enough lol well this was my story

1. Removed back panel.
2. Removed Entire control paned, control and switch units disconnecting wiring assembly from motor.
3 Tilted front and side panel assembly away from frame, tub assembly and motor transmission assembly.
4.Removed cap from top of agitator, removed bolt holding agitator. Removed agitator, this part was tricky since some corrosion on shaft made agitator very difficult to pull off.
4. From bottom of unit disconnected motor/transmission unit from wash tub.
5. Located clutch assembly and removed lock washers. Removed clutch and replaced with new one.
------------------------------------------------------------
Steps 1 thru 3 were unnecessary.
All that needed to be done was to removed the agitator assembly. then turn unit on it's side or back and removed motor and transmission from the bottom.

We had to take the motor out and remove the coupling, when putting it back together we had some problems because the washer was on its side and the lid was open. After putting the motor and coupling back together we tried to turn it on, unknowing to us the lid was open so nothing would happen, finally we realized the lid was open. The actual repair was not complicated, just human error made it seem than way

I loosened two screws which held the knob panel in place. I undid the two clips holding the cabinet and removed it. The pump has two clips holding it on, I removed those and the pump came free. Taking advice from these forums, I did not remove the hoses attached. I disconnected the wiring harnesses from the motor. The motor has 2 clips also, these being held on with screws. I removed the screws and the clips. THE MOTOR IS HEAVY.
You will see the coupling on the "spindle" of the motor. In my case, both plastic pieces were cracked in 2 places. I removed the old coupling and cleaned the "spindles" and lightly regreased.
The replacement pieces I ordered were the "improved" ones with the metal insert. They were a tight fit on the motor but I used a socket and hammer. (lightly). Line up the coupling pieces, reattach clips, DONT FORGET THOSE SCREWS HOLDING THE MOTOR CLIPS. Pump goes on next, etc. MAKE SURE ALL WIRING IS RECONNECTED! Cabinet goes back on, large clips holding cabinet to rear of machine go back on. Knob console flipped down and reattached.
Plugged it in and I was good to go! This washer is almost ten years old and this is the second time I have been able to bring it back from the dead, the first time being the agitator "dogs" wearing out. THANKS PARTSELECT!

We unscrewed the two screws at the back of the control panel. Holding the control panel on both ends
we pulled it toward the front of the machine, slightly and gently lifting it at the same time, removing it from the metal surround. Holding the control panel up off of the surround we rocked the surround forward and lifted it off the washing machine frame.
We could see where the leak was coming from. We took the hose clamps from the two ports, then
using a pair of pliers pulled the two clips that are holding the pump onto the shaft protruding from the
electric motor. We matched up the part on the web sight. Ordered the part then when it came in we just reversed the order putting the machine back together. The hardest and most time consuming
thing about this repair was the clean up of the washing machine. (Dirt and soap residue does
build up on the inside of the wash tubs.)

leaned washer back on wall at or more than 45degree undid two screws off of motor. pulled old part off put new on reinstalled motor Done

The hardest part was removing the machine's cabinet. 2 screws on either end of the control panel, tip the control panel back out of the way and remove 2 clips, then slide the cabinet off the front. Replacing the valve was very easy. I didn't need the mounting plate that came with it. At first it looked like the screw hole wasn't going to line up with the hole in the back of the machine, but then I noticed that the valve had a groove that allowed it to slide downward on to the back. Pretty easy overall.

Make sure you UNPLUG your washer first. It is also a good idea to remove the water intake hoses from the back to avoid damage to them or the valves.

Getting the outer panels off was the hardest part for me. There are 2 screws on the back of the function panel. You don't have to remove the screws completely, just until they are unscrewed from the bottom base. Then I gently pulled forward and up on the function panel and it flips back exposing the wiring. There is one wire harness plug that needs to be disconnected toward the center of the panel.
There are 2 large metal clips that are removed by pressing a flat head screwdriver into them. Press down and slightly toward the front of the washer and it will release the clip. Be careful, mine popped up and flew behind the washer.
Once the clips are removed you can pull the entire caging of the washer (top, front, right and left side panels as one) away from the machine. This will expose the entire innards of the washer.
In the front at the bottom is the water pump. It is very easily removed. Pinch the clamps around the hoses with a pair of pliers and move them up the hoses. Pull both hoses off the pump.
There are 2 metal clamps holding the pump in place. You can release them using a flat head screwdriver as well. Once free from clamps, the pump can be pulled straight forward to be removed.
Replace the pump with the new one, placing it in the same place and position as the old one. Attach the clamps back on. Mine were really hard to reattach as the tension was really tight.
Then slide the hoses back on and use the pliers to squeeze and slide the clamps back down the hoses to secure them to the pump.
Replace the cage of the machine. On my particular model, the front panel hooks under a metal lip and the side panels rest on them, so it was a challenge getting it back into place by myself in the small area I was working in.
Replace the metal clips on the top using the flat head screwdriver by pulling slightly toward the front of the washer and pressing down.
It was a little scary, I thought I was going to pinch myself.
Then reattach the one wire harness, flip the console back down and secure tightly.
Screw the 2 screws back in on the back of the function panel and your done. Reattach the hoses and plug in your washer.

This was my first washer repair. I did it with some sketchy online instructions for a different model washer. It took forever to get the washer open and was even more frustrating to put it back together. Changing out the pump was simple once I got in there. I saved over $100 in labor by doing this myself and in only took about 45 minutes.
I think I'm ready to open up the dryer and give it a good cleaning.

It took me awhile to figure out how to get the shell off the washer frame. (I didn't know about flipping it on its back). Once the moving parts were revealed, the water pump was staring at me with both ports. I turned the machine on and saw that the leak was coming from the pump.
1. Cut power
2. unclipped pump with pry with screwdriver
3. detatched both hoses - flood ensued
4. gently pulled pump off transmission
5. replaced pump

I reccommend doing this repair with empty tub.

Second time I did this. Same repair about 4 years ago. Pretty easy. Take the cabinet enclosure off, take pump off, remove motor and replace the coupling. Since the coupling is now reinforced with metal, a little more difficult to get on the drive shafts of the motor and the clutch drive?. $20.00 saved me $500.00 for now with a relatively easy repair and hopefully with reinforced part, it will last a little longer.

Removing top console control panel, deataching 2 clips and removiong the entire box to get access to the agitator and the direct drive, one part on the top and other on the bottom of the washer,removing top cap of the spinner got access to the agitator. Using 1/2" socked and pliers remove & rep[lace the agitator. for the direct coupling: remove the water pump (2 clips) 1/4" socked & screw driver remove the electrical Motor, remove & replace the direct coupling, put all removed parts back toguether, reasembly the box ataching clips on place, console panel Install, perform operational check, was good I have the washer running like a new machine.