11081375840 Kenmore Washer - Instructions

I followed the instructional video that referenced the water inlet valve. The steps I followed were identical to the video I watched. That was extremely helpful. The hardest part was removing the terminal wires that connected to the inlet valve, the rest was very easy. With the new valve installed the washer works exactly as it did before. This site is very helpful, thank you!

First - I saw the picture of the part on your site. It made all the difference.
Then, I turned off the water supply, unplugged the washer, removed the screws holding the backing plate on the washing machine to expose the valve.
After that, it was as easy as removing two mounting screws, disconnecting the solenoids (just two connections), pulling out the old valve and replacing it with the new.
Pretty simple and a lot less pricey when you can wait a few days for a part to come in the mail.

Had no problem in disassembling the unit to get to the water inlet valve area. Very little problem installling the inlet valve but had somewhat of a difficult time getting the housing reassembled. There is a good flow of both hot and cold water which has cut down on the fill up time and washing time. Glad it is still working after 15 years. Instructions on the internet were extremely helpful. The delivery time of part was amazingly fast.

I watched the video provided and followed the same steps in taking the washer cabinet off. The valve was very easy to replace and I took the opportunity to really clean and inspect everything. A little tricky to get back together but not bad. My 25 year old kenmore is working like a charm.

I replaced the water inlet valve. First I watched a YouTube video on the repair; surprised to learn that you take the machine apart from the front, not the back.A few tips; pull the washer all the way out first; have extra tools in case you have the same problem as I did that the flathead screws holding the old valve on the back were too tight and had a shallow slot; it took several wrenches and pliers to get them turning. Do NOT forget to hook the internal hose back to the valve before reassembling the machine;and pay close attention to how the housing of the washer fits onto the frame, so that you can more easily put it back together. It would be helpful to have a second person for that step. All said, it was pretty easy to replace the part and I probably saved $200 and didn't have to sit around for a repairman.

removed top panel and back panel
and then disconect the two wire fromm water inlet
fallow by removing screws.disconect water hose
then put back new part make sure i have all same conected as original put back panel top and back
conected hose for water back and electric .
then i turned 0n cold water perfect work hot water perfect warm perfect. problem fixed.
thanks. pedro

I wish I could be more specific, but I had a bit of trouble getting the back off the washer. I removed the control panel on the top of the machine and that allowed me to get to the two clips that secured the back onto the unit. The I removed additional screws on the back until I was able to pull the back away from the frame on the side where the valve was installed. after loosening the screws that held the valve to the back panel I was able to reach in and pull it out of the side. Once that was done, the rest was a breeze. I clipped the hose on the original valve and re-attached it to the new part. Then it was just a matter of reassembling and that went much, much faster than the disassembling. I reattached the water lines, plugged in the washer and it worked like a charm. I was very pleased with the whole thing. Also, I paid for standard freight, but received the part the following day after placing the order. Sweet.

Unplugged the washer and pulled out from wall as far as hoses would permit. Removed and drained both supply hoses. Removed drain hose and drained. Any water left in the tub will drain here so it's best to make sure it's drained prior to repair. Used pliers to hold the hose clamp and removed. Took screws out of drain hose interface plate and pulled out far enough to disconnect it from the internal hose.
Removed the two front screws of the control console. removed the two top hinge screws on the back. Removed four screws at the bottom of the rear access panel. Had to lift unclip several clamps holding the level hose in the control console and a cable connector. Unclipped various clips in the back panel to free it from wire bundle and such. Lifted the back panel up off of the clips located at the rear base of the control panel.

Removed two screws to free the solenoid assembly from the back panel. Unplugged the connectors to the original solenoid assembly. Disconnected the internal hose from it. Installed screw and plate supplied with the replacement solenoid to configure it with the same orientation as the original. Connected the internal hose and electrical connectors. Reassembled the back in reverse order as diassembled.

As I tore my ACL, my wife actually did the actual repair while I talked her through it. The video on your website was such a great help. Our repair went exactly as depicted.

I notice a screetching sound started and as time went on the water that flowed out to fill water drum was not working properly, unplugged washing machine electrical cord from outlet. disconnected water hoses, removed screws from control panel, pulled out front cover off wachine machine to access water valve, removed by unscrewing 2 screws, placed bracket on new part(placed over valve and pushed bracket up to slide and align srew to tightenbracket), put everything back in reverse order, helpfull video on video web site for visual

I followed the great step by step video instructions that you provided. The only difficulty was getting the plugs off the Water Inlet Valve. I had to use pliers (gently) to pull the two plugs off. I would highly recommend PartSelect to my friends.

looked on the find a part by s symptom. found the part,moved the washer took off the back.took 2 screws off of the top of the machine/controls.lifted the top.replace the water inlet valve.put it back together.easy repair.

I simply watched the video that PartSelect has online and it was a big help although my washer was a little different it still gave me the general idea on how to remove the casing. Great website! Thanks PartSelect!

I removed the faulty valve after unplugging the AC cord. Two screws, the two water hoses were removed, and the electrical connections were unplugged. The old valve could then be rotated so that the clamp on the fill tube could be loosened and the tube pulled off the valve.
The new valve body seemed to be an exact replacement, but the mounting bracked was slightly different and required drilling two new screw-mounting holes; an easy job.
Before securing the mounting plate to the machine, the fill tube and clamp were reattached, and the electrical connectors plugged in. After connecting the supply hoses and plugging in the AC cord, the machine filled with water properly and everything seemed to be back to normal.
I might have been able to use the original mounting plate, but it had been taken to a different location which was too far away to easily retrieve.

I just followed the instructions from a previous customer. Worked perfectly.