11024992300 Kenmore Washer - Instructions

We unscrewed the two screws at the back of the control panel. Holding the control panel on both ends
we pulled it toward the front of the machine, slightly and gently lifting it at the same time, removing it from the metal surround. Holding the control panel up off of the surround we rocked the surround forward and lifted it off the washing machine frame.
We could see where the leak was coming from. We took the hose clamps from the two ports, then
using a pair of pliers pulled the two clips that are holding the pump onto the shaft protruding from the
electric motor. We matched up the part on the web sight. Ordered the part then when it came in we just reversed the order putting the machine back together. The hardest and most time consuming
thing about this repair was the clean up of the washing machine. (Dirt and soap residue does
build up on the inside of the wash tubs.)

We had to take the motor out and remove the coupling, when putting it back together we had some problems because the washer was on its side and the lid was open. After putting the motor and coupling back together we tried to turn it on, unknowing to us the lid was open so nothing would happen, finally we realized the lid was open. The actual repair was not complicated, just human error made it seem than way

Disconneted hoses,unplugged.removed drain hose.Turned unit on its side.Unsnapped retainers,tryed to to pull off with just my hands,that didn't work.Used a pry bar to pop off.The end of the shaft was rusted out.I took a dremel with wire brush and cleaned up the end.Then the pump njust slid on.I took it off again and applied some anti-sieze on the end of shaft.then put pump back on.Snapped the retainers and put hoses back on.It was easy.When I first looked up washer parts,I found this other site and the price ws doulbe.Then I found you guys ,1/2 the cost and it was here in 2 days.Thank You Parts select.

removed water lines from back of washer. tilted washer to get access to the pump/ removed 2 hoses at pump and removed to snap clips attaching the pump. easiest repair i ever did. washer works fine now.

Started taking machine apart, would of been easier if I had looked at the online diagrams first, but dismantled enough to find a few broken parts, I could not tell the coupling was broke till I actually removed the water pump and motor. Total cost for 3 plastic parts was less than $25 including shipping. Received parts in 3 days on standard lowest cost shipping. Put machine back together, with just a few extra screws and wire clips, but machine works like new now. Much better than the cost of new or used washer.

I removed the cabinet and agitator, layed the machine on it's back, removed the pump, motor and gearcase. I found a way to prop the gearcase up so it rested level, removed the cover, drained the old oil. I removed all internal parts, disassembled them and cleaned them. I reassembled the gearcase using the new uetral drain assembly, and replaced the oil. I made sure the brake assembly was pushed into position and then put the gearcase, motor and pump back in. I sttod the machine up, put the cabinet back on and tested the machine. It still did not spin, so it wasn't the coupler, clutch or nuetral drain assembly.

I could not make the repair. If you get the pump specified on the shaft that drives the pump, the pump will be broken. I tried to call, nobody answers the phone. I ended up buying a Washing Machine and I'm stuck with a pump I cannot use.

Inserted new drain hose thru back and snapped into place. Tipped washing machine back, clamped new hose with pliers.

After the wife held the phone to the washer so I could hear the horrendous noise it was making. And I screaming at her "shut it off, shut it off!' I came home and took the agitator apart, and found the directional dogs worn out. Went to the computer and easily ordered new parts, which came very quickly. I took off the agitator with a long extension and socket, put in the new dogs and reversed for installation. Told the wife get back to doing the laundry!

Raised washer on cinder blocks high enough to get underneath, removed wiring, capacitor (because it got in the way), removed spring clips from pump, removed pump, no water spillage this way. removed clips from motor, removed motor, pulled old broken coupling rubber ring and plastic pieces out, used a spark plug driver to press new ones in place on the gear shaft and motor as they will fit tighter because they have a metal reinforcement that the original did not have, lined up the two halfs and clipped motor back on, cliped pump back on, reconnected wires again, lowered off the blocks and washed a couple loads that night.

I used pliers to loosen the hose clamps and the small springs that hold the water pump to the water pump motor. The old pump then came off by simply pulling it off. The new was was the reverse. Everything worked well.
The biggest problem had been finding that the water pump was leaking. I first tried to fix it with epoxy but it is apparentlly made of nylon and the expoxy didn't stick well.
I am still annoyed that Whirlpool makes a water pum that leads so soon. The Whirlpool site showed my model number as non existent. Later, after purchasing the right one from this third party site, Whirlpool sent email that they found the model number and gave me a much higher replacement price for the pump.

Just changed out the old pump with the new one. It went very quick and smooth!

Unpluged washer. Turned washer on its side, unpluged wire harness to motor. Removed hoses to pump on motor, removed screws and nuts holding motor, then pulled out motor. Popped off old couplings,intalled new, reassembled. Piece of cake!

i had to strip the outer housing of the wahing machine apart the remove the motoe from the transmission to get to the coupling. once i recived the coupling( which was very quickly) i just reversed those steps.

Hello the installation was real simple I first uplug machine from wall I turn off all water leading to in to the machine I then tip machine on it side I then took loose all wiring leading to the motor then motor is held up with 3 screws and 2 bands that hold it in place I reinstall the new motor coupling insert the wires and turn back on the water leading to machine then plug machine back in, every thing was good to go. . . . Save a lot of money doing it my self so simple to do. . . .