11021086000 Kenmore Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Debra from Ridgway, PA
- Parts Used:
- WP8054939
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lid seal was torn
Pulled off the old torn seal & in about 15 seconds had the new one put on, couldn't have been easier.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lana from Atlantic Beach, FL
- Parts Used:
- WP8054939
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Plastic piece had split
Very easy --just put it onto the metal and it slipped right on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sheila from Borger, TX
- Parts Used:
- WP8054939
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
wow!
I received the order quickly (although thought it could have been packaged in a much smaller box) and it took less than 10 mins to remove the old seal and replace with the new one. Only problem is the seal I ordered wasnt causing the problem ..lol so will be ordering again!!! Thank you!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruce from Hammett, ID
- Parts Used:
- WP8054939
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
rubber lid cushioning strip broke
the original piece had 3 metal clips that held the strip in place. It was a matter of sliding the strip off and sliding the new replacement part on. Time involved was less than one minute. It took longer to find the part than to install it. The part was ordered Thursday night and it was installed by Monday! Great service!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Erik from Atkinson, NH
- Parts Used:
- WP8054939
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The washer lid seal was torn and because, I think, I was getting a moldy/musty smell from the washer and in the clothes.
It was simple slide off the old seal and then clip on the new one. I also want to thank the workers at Parts Select, it was very simple and everything went great. I will be using them again and passing the word on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- kenneth from oregon city, OR
- Parts Used:
- WP8054939
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
lid gasket became older and brittle and eventually broke and cracked
Ordered the part and a couple of days later I popped off the old and popped on the new. It took longer to remove the part from the box than to install it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sandra from Hamilton, NJ
- Parts Used:
- WP8054939
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The original seal on had deteriorated and was coming apart.
Really nothing to it, especially since the original seal was coming apart. I just ripped it the rest of the way apart and removed it, then slid the new one on in its place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MILTON from SARASOTA, FL
- Parts Used:
- WP8054939
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Door seal worn out
When the part arrived I was busy, so my wife opened it and replaced the part.
Note: Parts Select is unbelievably quick. I ordered the part on Saturday night, selected the cheapest shipping method, and received the part on Tuesday.
Note: Parts Select is unbelievably quick. I ordered the part on Saturday night, selected the cheapest shipping method, and received the part on Tuesday.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Synthya from Temecula, CA
- Parts Used:
- WP8054939
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Rubber seal on the lid worn out
Old seal just kept falling off due to age wear. Took old one off (kept falling off) and popped the new one right in place. Very easy. Thanks Parts Select
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sandra from Hamilton, NJ
- Parts Used:
- WP8054939
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The old lid seal was breaking down
No problem - I've done this before. Pull the old one out (or wait for it to fall out) and pop the new one in. Very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alice from Ashland, KY
- Parts Used:
- WP8054939
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lid Seal Was Cracked
So Easy! Just slid old one off and sled new one on. This is the rubber seal that you touch when you open the lid. I was afraid I would get the wrong part but am so glad others left notes so I could tell this was the right one. And it definitely is worth the replacement cost.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Rockford, MI
- Parts Used:
- WP8054939
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
cracked lid seal
Pulled off old seal. Snapped on new seal. Takes longer to type it than it did to do it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dorothy from Washington, NJ
- Parts Used:
- WP8054939
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lid seal was old and cracked
So easy it's ridiculous, take the old one off, put the new one on! Can't say I love doing laundry, but I love my new washer lid seal! :)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from DuBois, PA
- Parts Used:
- WP8054939
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old seal split
Seal on the lid split. New seal easily replaced. It just snapped into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roger from Twinsburg, AL
- Parts Used:
- W10854425
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Broken clips
Turned off power and pulled power plug from the wall. Removed the two screws at the lint screen. Raised the top to by depressing the top spring clips. Removed the two 5/16" screws from front top. Removed wiring clips from front panel. Set the front aside while I removed the two broken panel clips. Installed the two new panel clips. reinstalled the front panel by placing the front panel above the sides. Opened the front panel door and supported the drum while allowing the front panel to slide down onto the new front panel clips. Reinstalled the wiring clip. reinstalled the two 5/16 screws. Turned the drum to ensure that the felt seals and drive belt weere installed properly. Lowered the top and reinstalled the two screws at lint screen. Reinstalled power plug and turned on power. No rattles or squeeks!!!
Was this instruction helpful to you?
Thank you for voting!