11048184790 Kenmore Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- WILLIAM from SEBASTIAN, FL
- Parts Used:
- WP688805
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
The dryer nob wasn't working the dryer knob broke off inside the unit
It was very easy to install the new parts successfully thanku parts select I will always keep using your business the representative was so helpful and understanding my problem I wish I could remember his name he was outstanding and a 100 thumbs up to him
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Theresa from Yardville, NJ
- Parts Used:
- WPW10254672
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Needed an adapter to run the appliance
Very easy,take off the old faucet screen and screw on the adapter. What I really liked was the ease of ordering the part. In less than 5 minutes I had located the part and ordered it. Less than 3 days later, I had the part. Way to go PartSelect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ellen from NYACK, NY
- Parts Used:
- WPW10119828, WP21097
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
machine wouldn't turn on when lid closed
replaced missing screw and pad and now machine works perfectly
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sam from Sharon, TN
- Parts Used:
- 285664
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
hose split
Pulled washer out from wall removed clamp and old drain hose addnew hose replaced clamp put washer back in plact connected drain to outlet simple operation
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from YUMA, AZ
- Parts Used:
- WP3967051
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
4 rubber snubbers were broke
After removing wash cover by unscrewing the 4 screws at the back, I disconnected the electric by pulling the plug connector, this makes for more room to get at the snubbers. Remove the ring that held the snubbers in place, replaced the 4 snubbers , replaced the ring, making sure the position is correct over the snubbers, replaced the cover. Very easy job
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- michael from LANSING, MI
- Parts Used:
- 285948
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
pump no longer worked
Put pump in the way it came out. Used shield from old punp. New shield supplied did not fit. Too large for this pump. Put out going water hose clamp on plugged in the two wires. Tighten the 3 screws and done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bobb from SANTA BARBARA, CA
- Parts Used:
- 285664
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Rats chewed through hose.
New hose was perfect, went on easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Virginia from SNELLVILLE, GA
- Parts Used:
- 285664
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Old drainage hose had a break in it.
Removed broken hose and replaced with new hose. My washer will be 21 years old in January.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from BIRMINGHAM, AL
- Parts Used:
- 285664
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Old outgoing water hose leaking
1. Need mop, bucket to catch leftover water in machine before you remove old hose. 2. Removed old hose by removing clamp. 3. Dried up any remaining water around fixture before attaching new hose. 4. Slide clamp to bottom of hose before attaching to machine. 5. Attached hose and clamp to machine where old hose was removed from. Make sure clamp is secure. (Please note that clamp that came with the new hose was too big. I used the old one. Worked perfectly). 6. Finally run a little water in you washer, then run out to test tightness and there is no leaks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jimmy from MEMPHIS, TN
- Parts Used:
- WP89503
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Old hot water inlet hose had budge at both ends.
Turn water off at the inlet valve of hose you are replacing. Disconnect inlet hose the washer and let water drain out in a bucket. Then remove old hose. Replace new hose to inlet valve then washer . Use pliers to tighten both ends. Turn on water to check leaks at both ends of hose.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ed from North East, MD
- Parts Used:
- WPW10254672
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Faucet adapter leaked
Replaced the faucet adapter, works fine
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Faye from Clearmont, MO
- Parts Used:
- 285664
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Wrench (Adjustable)
The drain hose was very old
My husband and a friend did the work. I was not there but was told that there was no problem. Everything is working well now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karen from Lafayette, IN
- Parts Used:
- WPW10254672
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Needed a faucet connector
I bought the portable dishwasher on Craigslist, and it didn't have the connector that goes on the kitchen faucet. Ordered it here, got it in a few days, and didn't need any tools - just had to screw it on. Good as gold!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Trisha from Oklahoma City, OK
- Parts Used:
- WPW10254672
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Could not fit hoses for portable dishwasher onto existing faucet
I knew I needed a faucet adapter, but thought I could just go to my local home depot and get the part...not so much. After 3 trips and not getting the part I truly needed I ordered the part from partselect. I received it literally the day after I ordered it, screwed in place with no tools, attached the coupler/hoses to the faucet and washed dishes. I wish I would have ordered the part from partselect before even bother with home depot. I would have saved myself a lot of trouble! Extremely happy! Thank you!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Irons, MI
- Parts Used:
- WPW10254672
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
No faucet adapter
I unsrew the faucet head, and attached th e adapter
Was this instruction helpful to you?
Thank you for voting!