11023024100 Kenmore Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Hoang from Fairfax, VA
- Parts Used:
- 285753A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
direct drive washing machine not spinning
Direct drive, no belt. Motor sounds like it's spinning but the agitator is not. Bought the coupling (that goes between the motor and the transmission) and replaced it in less than 15 minutes. Two screws and two clips to open the cover. Two clips to move the water pump out of the way. Two screws and two clips to take out the motor. Replace the coupling and reverse the steps.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- eddie from lockesburg, AR
- Parts Used:
- 285871
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
pipe had a hole
I pulled the hose off and notice their was a part # and I went online and type the part # and showed the part and cost. I order it and receive it within 3days. when the part arrive I replace the hose in minutes. If I can do so can you its that easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- mario from eastchester, NY
- Parts Used:
- 285753A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
the washing machine would pump the water out, but the agitator would not spin, and it was making noise.
The video that was shown about how to perform the repair was spot on. I wasn't sure exactly what part I needed. I took the advise from you stating that these symptoms I described usually meant that the part I ordered was the correct repair In 65% of the cases. I was delighted to see that when I followed the instruction video, and the motor was removed, there was my coupling, In several pieces. At that point I knew that I ordered the correct parts.
Thank You,
Mario for Eastchester, NY.
Thank You,
Mario for Eastchester, NY.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Tinley Park, IL
- Parts Used:
- WP8054939
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old seal fell a part and caused bad virbrations
Slid off the old and slid on the new part. Actually my wife did it with no help and was rather pleased with her self on not needing any help except ordering it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Matt from Roca, NE
- Parts Used:
- WP8546127
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Retainer clip for the pump missing, caused pump to fail
Pulled hoses off, unclipped the remaining retainer clip, slid old pump off. Slid new pump on replaced the old retainer clip and put the new one on, replaced the 2 hoses, done. It took mabey 10 min.
The part got there in less that 24 hours from the time I placed the order, with standard shipping! I was impressed.
The part got there in less that 24 hours from the time I placed the order, with standard shipping! I was impressed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from HUMMELSTOWN, PA
- Parts Used:
- WP3363394
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
pump did not pump water out
Put new one on work good, but now can't pump no more .the problem now is the spin cycal broke and I not going to fix it. Thank for the part work good.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- terry from ORTING, WA
- Parts Used:
- 285825
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Agitator top part not working, dog legs worn off
Took out old parts and put in news ones, super easy and works great!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joyce from Dallas, TX
- Parts Used:
- WP8054939
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Part was cracked and falling apart
Too simple. The old one practicaly fell off and all I had to do was push the new one into place. It locked itself in and was ready to use.
No more rattling or noise when it runs now.
No more rattling or noise when it runs now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Danbury, WI
- Parts Used:
- 80040
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Top agitator did not work
I removed the cover for the softener dispenser on the top of the agitator. Then reached in and removed the cover of the nut and washer which was very sticky and sealed with an o-ring. This took a bit of pressure. Then used a socket wrench with an extension to loosen the bolt and took the whole agitator out of the machine. Then I set the agitator on the floor and with a fine 12 inch long screw driver released the catches while turning and pulling the agitatior with my other hand and holding the lower agitatior on the floor with my feet. I then turned the upper part over and removed the cogs and holding mechanism.
Then I reversed the process after replacing the cogs with the new part. 25 minutes total.
Then I reversed the process after replacing the cogs with the new part. 25 minutes total.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dale from DOTHAN, AL
- Parts Used:
- 8316845
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Washer tub goes out of balance in spin cycle.
Found leveling spring loose on bottom of washer, the sheet metal on bottom of cabinet ad rusted through. Drilled new hole in sheet metal and installed new leveling spring. Greased hole with blue marine grease so it will last another 40 years.
Was this instruction helpful to you?
Thank you for voting!
Kenmore 80 Series Washer - Agitator Stopped Working
First I screamed at the ceiling, because I have a three year old and an infant, and the washing machine was dead. Then I went to youtube. It seemed like the "agitator dogs" were the issue.
In this spirit of any repair, I replaced them, and it was not the issue. I don't know what I expected.
Ceiling. YouTube. Pacing.
Then I figured it was this part - the motor coupling. I unplugged the machine and took out the drain tube. I leaned the machine back and propped it up with an empty detergent bottle, because those were abundant. Ratchet off a few bolts and the motor comes out. The coupling was indeed broken. The new one slips right in - I tapped it a few times with a mallet for good measure / vengeance. Ratcheted the bolts back on and tipped it back up.
Pros: Washer works now.
Cons: Everest-esque laundry pile to address.
But hey, it worked! I am no handyman and it wasn't too bad at all. Half hour tops.
In this spirit of any repair, I replaced them, and it was not the issue. I don't know what I expected.
Ceiling. YouTube. Pacing.
Then I figured it was this part - the motor coupling. I unplugged the machine and took out the drain tube. I leaned the machine back and propped it up with an empty detergent bottle, because those were abundant. Ratchet off a few bolts and the motor comes out. The coupling was indeed broken. The new one slips right in - I tapped it a few times with a mallet for good measure / vengeance. Ratcheted the bolts back on and tipped it back up.
Pros: Washer works now.
Cons: Everest-esque laundry pile to address.
But hey, it worked! I am no handyman and it wasn't too bad at all. Half hour tops.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- david from BREMO BLUFF, VA
- Parts Used:
- WPW10250667, WP63907
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
Shaking during spin cycle
Followed the video. Removed the case and holder clips (not really needed) and replaced the springs. It did nothing to stop the problem and there are no more fixes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Maryanne from BEND, OR
- Parts Used:
- 285664
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
Drain hose leaking
Followed instructions other customers provided for hose installation. Haven't installed agitator dogs yet. Need to watch the video on your web site.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Connie from BATON ROUGE, LA
- Parts Used:
- 285805
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
leaking valves
We watched a video on YouTube; it was very easy . We had to use the mounting bracket.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Helen from NASHUA, NH
- Parts Used:
- WP89503
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Leaking water inlet hoses.
Removed the old hoses and screwed on the new hoses.
Was this instruction helpful to you?
Thank you for voting!