11082994100 Kenmore Washer - Instructions

Clutch was noticibly worn compared to new part. Direct drive flange had broken, this part should be steel. found a you tube video that was simple to follow. no problems

The tough part was replacing the front cabinet.
I did consult the video for help on replacing the clutch spring.
Thank you for that bit.

I admit to taking too much apart, most of the cabinet back can be left alone.
Some of the plastic wire keepers/routers suffered, as well as the console hinges.

The newly reassembled washer works without a hitch, and truely it took me about 4 hours over several days to dissamble and reassemble.
It is louder in the audible range than before, but very serviceale for another 20 years, saints willing.

Purchased and installed PS1485646 COUPLING, MOTOR (Direct Drive Coupling). We googled "Washing Machine making a grinding noise. Several people suggested coupling probably broken. We located some instructions online regarding dis-assembly, sure enough,the coupling was broken. We ordered the part from Partselect.com. It arrived in three days, replaced the broken coupler. Washing machine back in business for around $20. Hooray! Thanks, Partselect!

I pulled the hose off and notice their was a part # and I went online and type the part # and showed the part and cost. I order it and receive it within 3days. when the part arrive I replace the hose in minutes. If I can do so can you its that easy.

The video that was shown about how to perform the repair was spot on. I wasn't sure exactly what part I needed. I took the advise from you stating that these symptoms I described usually meant that the part I ordered was the correct repair In 65% of the cases. I was delighted to see that when I followed the instruction video, and the motor was removed, there was my coupling, In several pieces. At that point I knew that I ordered the correct parts.
Thank You,
Mario for Eastchester, NY.

Direct drive, no belt. Motor sounds like it's spinning but the agitator is not. Bought the coupling (that goes between the motor and the transmission) and replaced it in less than 15 minutes. Two screws and two clips to open the cover. Two clips to move the water pump out of the way. Two screws and two clips to take out the motor. Replace the coupling and reverse the steps.

to change it was 1,2,3
thank you guys

It took a lot of surfing the internet to find good web sites for information. One was part select . I removed the cabinet from the washing machine per instructions. Then I replaced the suspension springs. That was easy. Took about 10 minutes. However, it didn't fix the problem. So I decided to replace all the suspension pads without a total tearing down the unit. It was almost impossible to put the new ones in because they don't press in easily. One other thing, there are plastic cups with pins in them that look like they are missing cotter pins. After hours of searching. I found partselect.com
THESE ARE THE SHIPPING PINS THAT KEPT THE MACHINE FROM MOVING AROUND DURING SHIPPING. THEY TOOK THE COTTER PINS OUT AFTER SHIPPING. THEY ARE NO LONGER NEEDED. My story ends here because my machine is still shakes violently. I have offered my washing machine for parts on our local freecycle website so as to keep it out of the landfill.

Watching videos identified what parts to purchase.
Once identified - WATCH EACH PARTS VIDEO (again).
Lessons learned:
1) better to NOT tilt the washer
2) watch (more than once) and learn from the videos
3) must difficult step was loosening the tub retaining nut without having a spanner wrench (used a hammer and a short / wide blade screwdriver)
4) ended up being the tub support was not sitting properly in the suspension plate
5) cleaned and changed parts while apart
6) running as good as new

Thanks!!

Went on line and ordered the piece I need. I got my socket set out, held the center piece in place then with the socket unscrewed the bolt. Popped the plastic washer off put the agitator clips in, put the plastic washer on and bolted it back together and was done. Easy as 1, 2, and 3.

Pulled hoses off, unclipped the remaining retainer clip, slid old pump off. Slid new pump on replaced the old retainer clip and put the new one on, replaced the 2 hoses, done. It took mabey 10 min.
The part got there in less that 24 hours from the time I placed the order, with standard shipping! I was impressed.

First used wet vac to get water out. Unplug electrical cord. Shut off water and unhook lines. Unhook drain tube. Flip over on side. Take belt cover off. two screws.
Took photos of parts removing just for re- install. Ordered parts from part select.com. Came in Two days. The dealer was on 12 days I gave up on them. I removed actuator two easy screws and pulled off electrical connection no tool needed. Then removed pump three longer screws Than other part. Make sure to label them in a ziplock baggie. Plus I removed hose clamp with pliers slide Back on hose and pull hose off. Then remove electrical connection on pump. If it makes you feel better label each with masking tape so I know where each connection goes. Then replace pump first with new one. Make sure you push it in hard then the screws. Don’t over tighten. Plastic parts break. Hook back up hose slide clamp back over fitting end with pliers. Hook up wire connector. Next hook up actuator. Two screws wire connector and your done. Put belt guard back on. Socks can get caught under washer get in belt and cause major issue. Then you need to reconnect water lines. Make sure hot goes to hot. Cold to cold. Drain hose hook back up. Plug in power cord. Now the fun part. Run a diagnostic and then calibration. See you tube videos it’s like 3 clicks to left then two to right with selector knob. Write down the exact amount of clicks and steps. It works. Be sure to turn knob 4 times to left to clear it like a combination lock. Don’t let the noises scare you it makes all
Kinds of sounds while calibration goes on.

will not go over step by step here as there are already a multitude of stories on site with exact situation as mine who have already done so.. What I will say is that PartSelect is easily the absolutely best site on the net for a complete problem diagnosis to finished repair experience. Just input your model # and describe the problem and you get instant diagnosis probabilities along with access to a long list of customer Q & A and reviews, along with step by step videos on diagnosing, dis- assembling, and re-assembling along with links to all parts needed and also some secondary tips along the way. The prices are fabulous (example: I got a clutch assembly kit with several parts and 2 additional parts as a just in case for $55 shpg incl, while my local appliance parts place wanted $59 plus tax for just the main part in my assembly kit with a no return policy and no part guarantee, plus it was only 1 day more to have PartSelect pkg arrive than I would have gotten part from local store). This site is FABULOUS !!!

Remove metal cover; remove pump, remove motor, remove tub spin assembly; remove transmission. Remove clutch be removing retaining ring. Installation was reverse. No problems, part worked like champ.

Note: Called Sears to see if I could get the part locally. Turns our I had to call an 800 number. Lady said that the part was not carried and would have to be shipped from warehouse. Tried to sell me some discharge hoses. Then said the part would cost $65 before S&H. Told her I didn't want to spend that much, she asked how much I wanted to spend and seemed upset when I told her your price. She didn't comp it, just said that theirs was an official part from Sears, blah, blah, blah. Anyway, thanks for the great service!

I did a Google search for the model number and found this site, PartSelect.com. Based on the diagrams on the site and what I could see underneath the washer, it was clear that the motor coupling was now gone and the shattered pieces of it were all over the floor. So I ordered a new coupling and waited for it to arrive, it was shipped in just a few days. Once I had the new coupling all I had to do was remove a couple of brackets holding the pump onto the motor, and the motor onto the gearbox; unplug the electrical terminals and lift the motor out. There are two halves to the coupling, one sits on the shaft of the gearbox and the other on the shaft of the motor. Both of these are seated into a rubber boot that is also a part of the coupling. Once the motor is sitting on the gearbox with all the coupling parts seated in place, just plug everything back in and replace the brackets. You will need a 1/4 socket to remove/replace the motor brackets. Also, it should be noted that you will want to unhook everything that is hooked to the wall (hoses, power cord) but it assumed you've already done this if you have access the the underneath of the washer.