11026058690 Kenmore Washer - Instructions

Remove the nut from the top of the motor shift inside of wsher. then remove the wire harness plug. Take out three bolts side the shaft and motor out. Replace clutch and install in reverse order.

took off two screws that held the top part on took the screws that held the back on 4 screws removed the one screw that held the replacement valve put the black mounting plate on the machine replaced screws very simple.

My daughter found the video on youtube, which showed step by step repairing procedures. I just followed it and fixed my dryer in 15 min.

I ordered the switch, which is what most people told me the problem was. I didn't have a multimeter, so I couldn't test the current one.

I removed the two screws from above the lid switch, removed the control panel screws on either side, and used a flat screwdriver to pry the top off by popping the clips.

The switch was easy to reach, and I compared the old and new switch after removing the paddle assembly. The new switch has three prongs, whereas my old one had two, so I put the gray wire terminal onto the bottom prong. I set everything down, plugged it in, and tested it, but still no spin cycle.

After some further research, I realized the problem was with the spin solenoid under the washer, or the red wire that leaves the lid switch and goes to the spin solenoid, also called a wig-wag solenoid. (This is a belt driven model, not direct drive.) It's not too common that the solenoids fail, but it is rather common that the wires break inside the insulation on this model.

Moral of the story is always ohm through the switches and wires before ordering replacement parts. (Remember, never ohm through a live circuit.)

After researching and learning from the university of YouTube, I ordered new agitator 'dogs' from PartSelect - the rubbery dogs which look like gummy bears, were worn out in my machine and needed to be replaced. These dogs secure the inner part of the agitator. After watching several videos on YouTube, I knew precisely what to do and what I needed. I researched and found PartSelect on-line and they were very helpful and sending me the dogs. It was a very simple fix, and my washing machine now is working like brand new. Thanks PartSelect for all your help and will reach out again for any future self-fix projects!!

Actually this is kinda funny. I ordered the part and it arrived when I was out of town on business. My 20 year old daughter tipped the washer up on its end, and replaced the pump herself in less than 30 minutes. Her only complaint was that no one told her to block the washer up as it almost fell on her.

First I removed hose from drain, next I loosened the clamp at the drain hose connection at the washer. Removed hose. Have rags/towels as there is some residual water that will spill out of the washer. Reinstall in reverse.

First, I'm glad I found PartSelect. The previous posts for this repair told me exactly how to replace the pump: I unplugged the washer and moved it out away from the wall (did not need to disconnect water hoses). Then I tilted the washer back and propped it up so I could get underneath. Using pliers, slid hose clamps back and disconnected hoses from pump. Using a screwdriver, popped off two clips, top and bottom, that hold the pump in place. Pump then slides right off the shaft. Installation is the reverse. Make sure you align the shaft with the pump. Delivery of my part was FAST - ordered it and got it the next day!

I removed three bolts from the transmission and two clips that hold the motor to the drive gear. I replaced the brake cam that had cracked and the lining. Now it works great ! Ordered part on Friday before two and it came Saturday at four.

Unscrewed the two screws that hold the water lines to the valve. Unscrewed and lifted the control panel, popped the two spring clips that hold the back panel against the housing. Pulled the valve just outside the back panel. Took off the internal water line and moved it over to the new valve. Took off both hot and bold electric plugs and moved them to the new valve. With the old valve off, I sled the new valve into place and screwed it to the back panel. Put the spring tabs back on the back panel and screwed the back panel back together. Plugged it in, attached the water supply lines and tested it. Worked fine.

we looked at the video first then my husband fit the proble boy! was i excited! all the stores tried to get me to buy a new one. thanks partselets!!!!!!!!!!!!!!!!!!!!!!!!!!!!

I pulled back off machine. A real pain. Not something you have to do although once the back is off, the whole cabinet just lifts off. Idealy: Remove agitator and reatiner clip, lay washer on it's side or face, Remove electrical connector form motor, remove two hoses from pump, (motor can be remove easily from transmission if desired. It's lighter), remove three 1/2" bolts, lift transmission w/clutch assembly out. Pay attention to orientation of flat washer and clip (remove). The cluch band is indside the silver cover. Pich together with pliers to relieve tension and lift out. There are three while pads that wear away and glaze over when they get too hot from slipping. Reassemble. Ths is from memory so I hope I didn't forget anything. Time to do it this way would probably only be 45 minutes.

The reason it took as long as it did was because the job is not in line as the work I normally do.
It would be a fairly easy job for an experienced repairman. (Taking the back off the washer was time consuming for me) The rest of the job was easy as the part was a perfect fit.
I remember having a problem blending hot/cold water for some time. Most recently, while washing a load the water did not want to shut off. I can't remember how I diagnosed the water not shuting off as a problem along with the water temp control, but it is now repaired.
With the new valve installed, water temp select is now OK and the water now shuts off as normal.

Removed the clips. Pulled out the old pump. After trying to get the new pump on the shaft of the motor, I realized that some corrosion had built up on the motor shaft. I got a small tack hammer and very lightly tapped the shaft to remove the corrosion. The pump then slid on the shaft with no problem. Replaced clips. Job complete.
The corrosion on the shaft cracked the plastic piece where the shaft connects and this is what caused the problem in the first place.

After taking the entire washer apart one time, we learned that we could take the top and front of the machine off only to repair it. I found Part-select online and with the model number locating the part was easy. It arrived within 3 days and with instructions I could easily replace the old part with a few tools. I spent dollars instead of hundreds for a new machine.