11020972992 Kenmore Washer - Instructions

leaned washer back on wall at or more than 45degree undid two screws off of motor. pulled old part off put new on reinstalled motor Done

I had given up on repairing the machine and placed order for a $650 washer. After returning to home from this shoping, I wanted to know possible problems with the current machine and came across a story on your web site attached to the Coupling parts description. It described the repair details. Encouraged I placed order for this $15 parts and repaired in an hour, saved the replacement machine cost. Thanks a lot

removed water lines from back of washer. tilted washer to get access to the pump/ removed 2 hoses at pump and removed to snap clips attaching the pump. easiest repair i ever did. washer works fine now.

I ordered the new cogs but didn't want to wait the few days for them to arrive. So I decided to try and temporarily repair the old ones. After looking at the picture of the new ones on this site I realized that the teeth were just worn down. I took all four of them out and used a grinding disc to carve the teeth down deeper. They were not perfect. (I would recommend holding the teeth with a vise.) However, after reinstalling the cogs the machine worked perfect and that was two weeks ago. I'm not going to install the new ones until I have to.

Watch the video

Disconneted hoses,unplugged.removed drain hose.Turned unit on its side.Unsnapped retainers,tryed to to pull off with just my hands,that didn't work.Used a pry bar to pop off.The end of the shaft was rusted out.I took a dremel with wire brush and cleaned up the end.Then the pump njust slid on.I took it off again and applied some anti-sieze on the end of shaft.then put pump back on.Snapped the retainers and put hoses back on.It was easy.When I first looked up washer parts,I found this other site and the price ws doulbe.Then I found you guys ,1/2 the cost and it was here in 2 days.Thank You Parts select.

I could not make the repair. If you get the pump specified on the shaft that drives the pump, the pump will be broken. I tried to call, nobody answers the phone. I ended up buying a Washing Machine and I'm stuck with a pump I cannot use.

Looked at the repair instructions on your web site and it made the repairs simple and easy.

I followed the online instructions and found it remarkably easy. I saved a lot of money and will certainly use PartSelect in the future! Washer works like new again!

Yes, I agree that the actual replacement of the pump was an easy task on this whirlpool washing machine, however, unlike other posters, I had no access through the bottom of the machine. My machine has a solid pan on the bottom. It has a large hole in the center - I think to access the transmission, but no access where the pump is.
So, I had to dismantle the entire enclosure, first the back (about 6 screws, a couple of electrical connections, etc.), then remove the rest of the enclosure to reveal the guts of the machine. I also had to disconnect a small vacuum tube attached to the tub, and remove the control console on top along with the back. It was pretty straight forward, took about two hours to dismantle. Then, the actual removal of the pump was as easy as others have described here - two spring clips and a hose clamp and I had it in my hand. I ordered the new part, which came very quickly - 2 days I think. Then I took another two hours to re-assemble the machine. It works - yeah!
Symptoms - water leak on the floor, it was actually intermittent for a time, so I procrastinated. Then when I actually did the work, I could see the rust trail and follow it to the leaky pump. The pump was actually leaking through the center, where the drive shaft from the motor goes. There is probably a seal between the impeller and the central drive slot that gives out after a while.
New pump in - machine back together - no leaks.

Second time I did this. Same repair about 4 years ago. Pretty easy. Take the cabinet enclosure off, take pump off, remove motor and replace the coupling. Since the coupling is now reinforced with metal, a little more difficult to get on the drive shafts of the motor and the clutch drive?. $20.00 saved me $500.00 for now with a relatively easy repair and hopefully with reinforced part, it will last a little longer.

i had to strip the outer housing of the wahing machine apart the remove the motoe from the transmission to get to the coupling. once i recived the coupling( which was very quickly) i just reversed those steps.

Make sure you UNPLUG your washer first. It is also a good idea to remove the water intake hoses from the back to avoid damage to them or the valves.

Getting the outer panels off was the hardest part for me. There are 2 screws on the back of the function panel. You don't have to remove the screws completely, just until they are unscrewed from the bottom base. Then I gently pulled forward and up on the function panel and it flips back exposing the wiring. There is one wire harness plug that needs to be disconnected toward the center of the panel.
There are 2 large metal clips that are removed by pressing a flat head screwdriver into them. Press down and slightly toward the front of the washer and it will release the clip. Be careful, mine popped up and flew behind the washer.
Once the clips are removed you can pull the entire caging of the washer (top, front, right and left side panels as one) away from the machine. This will expose the entire innards of the washer.
In the front at the bottom is the water pump. It is very easily removed. Pinch the clamps around the hoses with a pair of pliers and move them up the hoses. Pull both hoses off the pump.
There are 2 metal clamps holding the pump in place. You can release them using a flat head screwdriver as well. Once free from clamps, the pump can be pulled straight forward to be removed.
Replace the pump with the new one, placing it in the same place and position as the old one. Attach the clamps back on. Mine were really hard to reattach as the tension was really tight.
Then slide the hoses back on and use the pliers to squeeze and slide the clamps back down the hoses to secure them to the pump.
Replace the cage of the machine. On my particular model, the front panel hooks under a metal lip and the side panels rest on them, so it was a challenge getting it back into place by myself in the small area I was working in.
Replace the metal clips on the top using the flat head screwdriver by pulling slightly toward the front of the washer and pressing down.
It was a little scary, I thought I was going to pinch myself.
Then reattach the one wire harness, flip the console back down and secure tightly.
Screw the 2 screws back in on the back of the function panel and your done. Reattach the hoses and plug in your washer.

This was my first washer repair. I did it with some sketchy online instructions for a different model washer. It took forever to get the washer open and was even more frustrating to put it back together. Changing out the pump was simple once I got in there. I saved over $100 in labor by doing this myself and in only took about 45 minutes.
I think I'm ready to open up the dryer and give it a good cleaning.

Old machine and vibrations are still there but weaker. Seemed to turn counter clock wise. Put a 4x4 board behind in order to stop the twisting, and keep hoses safe from vibrating and causing wear. Stays fairly stable now.

First. I unplugged the washing machine from the electrical source. Then, I unscrewed the two screws in the front and the two screws on the back holding the control panel onto the washer. I lifted the control panel off and let it hang in the back of the washing machine. I unplugged the white plug connecting the control panel from the machine. I used a screw driver to pry the two giant spring like clamps and the cabinet released from the actual washing machine. At the bottom, I found the pump, unclamped the small clamps holding the pump on, pulled it off, installed the new one ( I used pliers to get the hose clamps where they needed to be) and then reversed by steps. Easy as pie and saved me a bunch of money