11084090600 Kenmore Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Bruce from Englewood, CO
- Parts Used:
- 285805
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Wahing machine overflowed
Opening the washing machine, and removal and replacement of the water inlet valve were both trivially easy. However, getting the cabinet back into place was a bit tricky, only because I did it by myself. It was surprising how flexible and flippy-floppy the cabinet became when free of the structure of the machine. It would have been a huge help to have had a buddy over to just help place the back corners of the cabinet into place. That would have made the whole job totally easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sandra from Ash Flat, AR
- Parts Used:
- 285805
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable), Wrench set
Cold water inlet valve went out
My son did the repair. Thank God for Sons who know how to repair things. Worst thing was figuring out how to get the back off, top where dials are had to come off too. the rest was easy according to him..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karen from Austin, TX
- Parts Used:
- 285805
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
There was very little cold water coming through.
I'm a 61 year old single woman, rather handy around the house. I followed the video which was very helpful and everything went together fine until it came to putting the body of the machine back on. I did the repairs all myself which took about an hour but when it came to the machine body I couldn't get it back on there after numerous tries. I had to call my brother and it took him just one try but then he is 6'2" and could look down the little hole to see where the tab was to put it on and hold the body at the same time. BTW - he did inspect my work before finishing the job and said I "did good!" Thanks for the video but could have used some hints as to how to put the body on with some close ups as to what he was doing with his hands when he did it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jodimarie from Easthampton, MA
- Parts Used:
- 285805
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Fill did not shut off one morning, resulting in washer overflowing..... Bummer.
I own a small, local handyman service as a Father/Son team. This repair is PERFECT for an apprentice to do as a confidence biulder. He learned the safe way to service a machine with garanteed success. This is a job anyone with basic knowledge can easily do with a little on-line homework on their machine. -Jim & Tom W.-
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marc from Whittier, CA
- Parts Used:
- 285805
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Washer would not fill hot water
This was a thirty year old Kenmore washer. I removed the control frame, and then removed the two nuts holding the water inlet valve. The valve itself was easy, two water lines and one fill line. Reassembly was problematic as this valve was not exactly the same, I just tied off the valve to the water lines so it would not move.
Of course what took the most time was a run to Home Depot as the hot and cold water hoses were old and I replaced them with new.
Of course what took the most time was a run to Home Depot as the hot and cold water hoses were old and I replaced them with new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gordon from North Stonington, CT
- Parts Used:
- 285805
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
very slow cold water flow
Followed the instructions on the Part Select video which were very clear. I removed control module from top of washer, pulled the washing machine outer housing forward slightly and disengaged the rear closure panel slightly. I disconnected the electrical harness and then I was then able to remove the existing inlet valve. The new valve was then installed and the precess reversed to complete the installation.
Piece of cake!! (The water comes pouring into the machine now)
Piece of cake!! (The water comes pouring into the machine now)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from Scottsburg, IN
- Parts Used:
- 285805
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Cold water flow very slow
Our washer's cold water flow became very slow. We were living with just hot water washing for about a month. I had used PartSelect in past and have always been very satisfied with the outcome. So, I went on the site and within a couple of minutes of navigating, had the part (water inlet valve with mounting plate) on order.
I watched the repair video on the water valve ordering page. My installation went pretty much to this procedure, with one exception, I had to use the mounting plate, which I don't think was covered in the video. You have to read and follow the instruction sheet that comes with the part. Therefore, my installation instructions are to a) watch the video, b) get together all the recommended tools described in the video, c) be prepared to use the mounting plate (which uses the same 1/4 nutdriver the video says is needed).
I did the complete valve replacement and had the washer back in place in just at 30 minutes, the tight closet quarters added a bit to this time I'm sure. Working in a basement or open utility room would have been a little easier and quicker. My shortfall though is, I should have done the hose connection check (turning the supply valves back on) before making the move back into the washer space, as once I performed what I thought was my last step, turning on the supply valves, I heard a water leak. This was resolved with another 10 minutes worth of moving the washer back out, disconnecting the hose, removing the rust debris which apparently caused the leak, reconnecting the hose, and this time, checking for leaks BEFORE moving the appliance back into place. I think the time estimate of 30 minutes is good for individuals with moderate experience in appliance repair, and probably good for the novice in conjunction with the video.
I watched the repair video on the water valve ordering page. My installation went pretty much to this procedure, with one exception, I had to use the mounting plate, which I don't think was covered in the video. You have to read and follow the instruction sheet that comes with the part. Therefore, my installation instructions are to a) watch the video, b) get together all the recommended tools described in the video, c) be prepared to use the mounting plate (which uses the same 1/4 nutdriver the video says is needed).
I did the complete valve replacement and had the washer back in place in just at 30 minutes, the tight closet quarters added a bit to this time I'm sure. Working in a basement or open utility room would have been a little easier and quicker. My shortfall though is, I should have done the hose connection check (turning the supply valves back on) before making the move back into the washer space, as once I performed what I thought was my last step, turning on the supply valves, I heard a water leak. This was resolved with another 10 minutes worth of moving the washer back out, disconnecting the hose, removing the rust debris which apparently caused the leak, reconnecting the hose, and this time, checking for leaks BEFORE moving the appliance back into place. I think the time estimate of 30 minutes is good for individuals with moderate experience in appliance repair, and probably good for the novice in conjunction with the video.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marco from Somerville, MA
- Parts Used:
- 285805
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
water inlet valve was cracked on back of washing machine
i removed all screws for back of washer and removed top washer controls. then removed the valves and replaced with new one. reinstalled back in reverse order.really easy job. you just have to pay attention how you took it apart and study how it works , thanks!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- BRIAN from NEW ORLEANS, LA
- Parts Used:
- 285805
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
machine stopped running hot water
replaced valve. Everything now working. Ordering the part was simple and I found a how to video on line that was great The whole replacement of the defective part was easy and the machine was back on line in 30 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from Brockton, MA
- Parts Used:
- 285805
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Socket set
Water would not shut off plus long time filling
I simply watched the video that PartSelect has online and it was a big help although my washer was a little different it still gave me the general idea on how to remove the casing. Great website! Thanks PartSelect!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JAVIER from LOS ANGELES, CA
- Parts Used:
- 285805
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
screeching sound along with small amount of water coming out to fill machine
I notice a screetching sound started and as time went on the water that flowed out to fill water drum was not working properly, unplugged washing machine electrical cord from outlet. disconnected water hoses, removed screws from control panel, pulled out front cover off wachine machine to access water valve, removed by unscrewing 2 screws, placed bracket on new part(placed over valve and pushed bracket up to slide and align srew to tightenbracket), put everything back in reverse order, helpfull video on video web site for visual
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- scott from mooresville, NC
- Parts Used:
- 285805
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Socket set, Wrench (Adjustable)
washing machine over flowing
easy repair and so far so good stopped over filling so far hope this helps ... scott
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Roswell, NM
- Parts Used:
- 285805
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Cracked / leaking water valve
Rmoved top, removed back, replaced valve.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Oakland, CA
- Parts Used:
- 285805
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Leaky Inlet Valve
This is a very easy repair. After shutting off the water, removing the feed lines, and of course unplugging the electricity, all I had to do was: 1. remove two screws 2. flip the control panel up 3.unplug a wiring connection 4. pop two clips that hold the housing to the back 5. lean housing forward 6.unplug wiring at valve 7. remove fill hose 8. remove two screws. 9. toss old valve in the recycling bin (or trash depending on your area) 10. Reverse procedure using new valve. 11. wash clothes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jason from Sterling, VA
- Parts Used:
- 285805
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Wasn't flowing cold water effectively
To Whom It May Concern:
I had issues with my washer not flowing cold water very efficiently.
I was convinced I was going to have to spend at least $200 to get
someone to fix it or buy a new unit. My friend showed me your site
and videos. I quickly found the part I needed, had full confidence
that my problem would be solved with that part and that I'd be able to
do it myself. I ordered the part yesterday, got it today, and
installed it in under 15 minutes (thanks to the excellent video).
What an amazing customer experience!!
This is the greatest buying process I've every had with an Internet
purchase....hands down!! You saved me a couple hundred bucks and made
it fun and easy for me to fix myself. You guys are the best. No
doubt about it.
Thank you so much, Jason
I had issues with my washer not flowing cold water very efficiently.
I was convinced I was going to have to spend at least $200 to get
someone to fix it or buy a new unit. My friend showed me your site
and videos. I quickly found the part I needed, had full confidence
that my problem would be solved with that part and that I'd be able to
do it myself. I ordered the part yesterday, got it today, and
installed it in under 15 minutes (thanks to the excellent video).
What an amazing customer experience!!
This is the greatest buying process I've every had with an Internet
purchase....hands down!! You saved me a couple hundred bucks and made
it fun and easy for me to fix myself. You guys are the best. No
doubt about it.
Thank you so much, Jason
Was this instruction helpful to you?
Thank you for voting!