11020892990 Kenmore Washer - Instructions

Followed the excellent video instructions. They say you can perform the repair without removing the enclosure, but when I saw how easy it was to remove it, it definitely improves the access and speeds the repair. Have a piece of wire handy to to hold the pump assembly out of the way. Installed new clutch kit and it runs like a champ.

Followed the videos on the website. But had to order parts twice because it wasn't the springs it was the plastic bushings the tub sits on that caused the wobble. No big deal though. All told it was still far less expansive than a new machine.

First, I read the previous repair stories, so I knew what step to do first. So, first I took the hose off of the drain, then I removed it from the washer. And as the previous repair story stated, some water came out and I had a towel ready to catch the water that was in the hose. I threaded the clamp onto the new hose, pushed the new hose onto the washer, used the pliers to open the clamp to better clamp the hose onto the washer. Then, placed the drain hose into the drain pipe and it was done! Thanks for such a great site!

I watched the video from the web site, decided that pulling the whole case was more work than needed. I tipped the washer back at about 45 degrees so that I could get under it and braced it so that it would not fall back fwd. Put a medium cooking bowl under the pump, used a channel locks to remove the 2 spring clamps that where around the hoses and slide the hoses off and let the water drain into the bowl. Then used a medium straight slot screw driver to release the clips from each side of the pump and slid the pump off the shaft. If you turn the clips 90 degrees they will slip out and had to remove the upper clip to get the pump out. Lined up the pump and the shaft making sure that the flat side of shaft and pump lined up and slid it on. Reinstalled the pump clips and slid the hoses back on the pump slide the clamps back in place lowered the washer and test ran it for leaks. Great Job NO leaks. Whole job took me less than 30 minutes.

After removing the 2 phillips screws at the base of the control panel, I flipped the panel toward the back. Using a screwdriver, I popped off the spring clips, releasing the cabinet. I removed the 1/4" hex head screw on the spring mount and removed the old spring and replaced with the new. I repeated this with the other 2 springs. The spring bracket in the rear also holds the tub balancing spring. It is easily replaced while replacing the suspension spring.
If this didn't fix the problem, we were going shopping for a new washer. After this repair, it operates like new!

Remove the washer case/enclosure to expose all the internal parts. Lie on the floor and with pliers and a strong arm. Remove and replace each spring one at a time. Pretty straightforward.

I did the repairs after watching a few videos on this web site and it covered everything I needed. Went well and the parts were perfect.

Followed the video on the website. I removed the hoses from the pump rather than removing the pump as suggested in the video. Then separated the motor from the transmission and replaced the coupling; then reattached the motor and hoses. Lining up the washer cover and clamping it back on was the most trouble. But all in all, a easy repair.

just like video showed really helpfull

diconnected water supply and discharge, unplugged the unit, removed the aggitator, laid the washer on it's back, romoved the hoses from the pump, took out 3 bolts, removed the motor/transmission and replaced the clutch and put it all back together.

I removed the back of the washer, removed the old water inlet syphon, replaced it with the new one, and, with some difficulty, replaced the back of the washer, reattaching all of the parts to it.

The dispenser ring was loose due to the broken plastic dispenser. Replacement was too easy.
Removed the old, and snapped the new one in place. Took all of 1 minute. Now I'm back up and running

A label was created and never shipped. Sat there for 2 weeks.
Contacted company for a refund and a Retha’s never been issued.
Terrible service!

I was familiar with the Kenmore / Whirlpool direct drive mechanism but at first I could not determine how to release the console. I finally found the end cap trim pieces would pop off revealing the 2 screws that hold the console in place. After removing them the console flips up and over the backboard. I then removed the 2 clips that hold the cabinet to the backboard, unpluged the lid switch connector and then tipped the entire cabinet forward and off the frame. This gives you access to the entire washing machine mechanism.
Next I released the 2 metal clips that hold the pump on and push it out of the way leaving the hoses connected. Next I released the 2 clips that hold the pump on, these clips also have a screw to secure them. I was then able to set the motor to the side without removing any wires.
The coupling parts had broken and were already off of the motor shaft and the input drive shaft of the transmission. I put the new drive parts on and had to tap them down untill they were flush with the end of the shafts. I then put the rubber coupling on the transmission drive end and aligned the motor drive to mate into the other holes in the coupling as I put the two back together. I then re attached the 2 motor clips with screws and reinstalled the pump with it's clips. I then reinstalled the cabinet onto the frame and replaced the cabinet clips. I then plugged in the lid switch connector and flipped the console back over and screwed it down. I then reinstalled the trim caps that had me stumped to begin with. The unit tested out OK.

Disconnected old power cord inside control cabinet, removed strain relief , then removed damaged power cord. Reinstalled new cord with new strain relief.