1106733409 Kenmore Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Trisha from Oklahoma City, OK
- Parts Used:
- WPW10254672
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Could not fit hoses for portable dishwasher onto existing faucet
I knew I needed a faucet adapter, but thought I could just go to my local home depot and get the part...not so much. After 3 trips and not getting the part I truly needed I ordered the part from partselect. I received it literally the day after I ordered it, screwed in place with no tools, attached the coupler/hoses to the faucet and washed dishes. I wish I would have ordered the part from partselect before even bother with home depot. I would have saved myself a lot of trouble! Extremely happy! Thank you!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Becky from Stanley, NC
- Parts Used:
- WPW10254672
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench (Adjustable)
The Faucet Adapter was worn out.
Ordered a new Faucet Adapter! Simple
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Norm from Hamilton Square, NJ
- Parts Used:
- WPW10254672
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
A gift portable dishwasher did not have the faucet adapter.
Found the adapter on Parts select through a google search. Unscrewed the existing faucet aerator and srewed in the adapter. The plastic shrink wrap holds the washer and screen in place, so don't open it until you're ready to install. Finger snug does it, only use the pliers to remover the old aerator from the faucet. Normally, I don't use pliers, but both of these parts were round and had vertical serrations to engare the plier teeth.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Irons, MI
- Parts Used:
- WPW10254672
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
No faucet adapter
I unsrew the faucet head, and attached th e adapter
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ed from North East, MD
- Parts Used:
- WPW10254672
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Faucet adapter leaked
Replaced the faucet adapter, works fine
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kim from Oviedo, FL
- Parts Used:
- WP21258
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Missing lid hinge bearing
1) Using a Phillips head screwdriver, the two screws retaining the hinge pin to the lid were removed. 2) Remove hinge pin and tilt lid slightly to gain access to bushing hole. 3)Install new bushing in hole. 4)Reposition lid. Insert hinge pin through lid and into bushing. 5)Reinstall hinge pin retaining screws and tighten.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Cameron, NC
- Parts Used:
- WPW10254672
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
changed out kitchen sink faucet set
replaced the faucet adapter I did not save when I change out the kitchen sink faucet set
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Forrest from Oxford, AL
- Parts Used:
- W10814296
- Difficulty Level:
- Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
Washer leaking
After watching some on-line vids, I determined it was the center post, or tub, gasket at the bottom. A cheap part, and easy to snap-out the old and snap-in the new - But - I had to dissassemble the washer into individual washer component molecules. Luckily, I'd done this recently to replace the clutch drive, then the motor, then this. Not too bad, really. Washer body off (2 screws and two snap-links); agitator out (7/16" socket on extension); bang off tub nut (heavy hammer and punch); bang off drive block (hammer again); and pull tub up an out. Tub drain disconnected (pliers); pull off level sensing tube; three spring mounts (nutdriver); then just yank tub up. Poke out Centerpost gasket; snap in a new one; reassemble. Piece of cake.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruce from Yankton, SD
- Parts Used:
- W10814296
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Socket set
Had issues with removing the inner tub
Had a lot of corrosion on the shaft area and had a hard time removing the inner tub but after some WD-40 and unprintable words and labor it popped off. Cleaned everything up, shaft, inner drum and outer drum. After that everything was a piece of cake. Thanks for the help!
Was this instruction helpful to you?
Thank you for voting!