11074411100 Kenmore Washer - Instructions

We watched a video on YouTube; it was very easy . We had to use the mounting bracket.

Removed screws from top control panel. Tilted panel back. Unsnapped two retaining clips and pulled entire washer cover forward. Turned off water and uplugged washer. Disconnected hot and cold water supply. Disconnected supply tube from water inlet valve. Disconnected electrical hook-ups to water inlet valve. Removed water inletvalve. Installed new valve being careful to use new mounting plate supplied and making sure screw holes line up correctly. Re-connected all disconnects and it works like new!

There are two screws that hold the switch in place. And two wires connected to the switch. The most difficult part of replacement is to place the new switch and hold it in place to reinstall the mounting screws. The space to work in is limited unless you remove the front panel from the dryer, which I opted not to do.

Installed part, now it works great!

The hardest part was removing the machine's cabinet. 2 screws on either end of the control panel, tip the control panel back out of the way and remove 2 clips, then slide the cabinet off the front. Replacing the valve was very easy. I didn't need the mounting plate that came with it. At first it looked like the screw hole wasn't going to line up with the hole in the back of the machine, but then I noticed that the valve had a groove that allowed it to slide downward on to the back. Pretty easy overall.

Unplugged it. Removed the two screws holding the panel on. This model had the screws on the front. Unplugged the wire harness and tipped the control panel back. I popped off the clips for the cabinet and slid it off the frame. On the back of the washing machine, I unscrewed two screws that held the water inlet valve in place. I unhooked the two wire harnesses on the inlet valve. Slid the clamp on the small hose back and pulled the hose off the inlet valve. Once I had the old part off, it was just a matter of doing it all in reverse. I did have to screw the metal plate that came with the part onto the part before I installed it. I put the small hose onto the new inlet valve and slid the clamp back in place on the hose. Put the new valve through the holes on the back of the machine, and replaced the two screws. Click the two wire harnesses back on, making sure to put the RED harness on the HOT valve (the holes have the stamp H and C on the back of the machine itself. Slid the cabinet back into place. Put the wire harness back on. Replaced the cabinet retainer clips. Slid the control panel back into the slots and replaced the two screws for it. That was it. All told it took me 15 minutes total. This was an extremely easy repair.

First used wet vac to get water out. Unplug electrical cord. Shut off water and unhook lines. Unhook drain tube. Flip over on side. Take belt cover off. two screws.
Took photos of parts removing just for re- install. Ordered parts from part select.com. Came in Two days. The dealer was on 12 days I gave up on them. I removed actuator two easy screws and pulled off electrical connection no tool needed. Then removed pump three longer screws Than other part. Make sure to label them in a ziplock baggie. Plus I removed hose clamp with pliers slide Back on hose and pull hose off. Then remove electrical connection on pump. If it makes you feel better label each with masking tape so I know where each connection goes. Then replace pump first with new one. Make sure you push it in hard then the screws. Don’t over tighten. Plastic parts break. Hook back up hose slide clamp back over fitting end with pliers. Hook up wire connector. Next hook up actuator. Two screws wire connector and your done. Put belt guard back on. Socks can get caught under washer get in belt and cause major issue. Then you need to reconnect water lines. Make sure hot goes to hot. Cold to cold. Drain hose hook back up. Plug in power cord. Now the fun part. Run a diagnostic and then calibration. See you tube videos it’s like 3 clicks to left then two to right with selector knob. Write down the exact amount of clicks and steps. It works. Be sure to turn knob 4 times to left to clear it like a combination lock. Don’t let the noises scare you it makes all
Kinds of sounds while calibration goes on.

Stopped by a friend who is an appliance repair person. He walked me through the Roper repair.
Removed the two screws, pulled the control panel up and back, disconnected the two wires. Sprung the two clips with a large screwdriver. That gave me the room I needed to do the repair. The hardest part was lining up the cover to go back on level. Part worked perfect, everyone was happy.

Followed the instructions. Removed two screws on front panel, flipped it up and popped up the retainer clips. Tipped the washer body forward. Unscrewed the old valve and replaced with the new. Reversed the previous procedures and put the whole thing back together. I had put up with this low flowing water for a couple years. Now it fills like new!

First I unscrewed two screws holding the back panel. Unscrewed the screws holding the water valve onto the back panel. With a screwdriver, pried the panel out far enough to pull the old water inlet valve out. Remove the connections on the old valve and replace with the new one. Screw everything back together. Fairly easy repair. Cold water flows like new and the noise is gone. Hope to get another few years out of the washer for this $25 fix.

The replacement of the water inlet valve was not too difficult after reading the steps posted by others. The main step is to unscrew the top control panel first, remove the top 2 screws of the back panel, and you have easy access to the water inlet valve. No need to remove the entire back panel. Follow the instructions which accompany the replacement water inlet valve and you should have no problems. The washing machine now fills faster with the replaced water inlet valve. The replacement inlet valve arrived within 2 days of ordering! Thanks for the superfast shipment!

Removed two screws holding top control section on, and folded back the control panel. Removed two clips holding cabinet on, tipped cabinet toward me and off. Removed and replaced water valve, being careful to mark hot/cold hoses, and secure the internal hose to the valve with the spring clamp. Most difficult part was lining back up the cabinet when putting it back on the base, but a few minutes to line up tabs and get the front of the cabinet UNDER the front groove in the base got it secure. Works fine now.

Initially, we thought the problem was in the water inlet valve and we changed it out. It went OK although the Kenmore almost fell apart after the removal of a few screws and the control unit.
Only thing was that it was unncessary. The real problem was not in the cold water turn on valve, but in the hose. The hose was special in that it was designed to shut off under emergency conditions. It appeared to be able to passs water when tested at my sink, but when connected to the washing machine and under presssure, it would not pass water. I had installed the part by this time so I left it there. I found the Kenmore washing machine rather flimsy in it's construction and tended to totally come apart once a few screws were removed.

1. Unplug washer, close hot and cold water supplies and remove water hoses from washer inlet valve.
2. Remove two screws at the bottom of the front of the control panel.
3 Remove two screws at the top of the back side of the control panel.
4. Remove control panel.
5. Remove two retainer clips that hold the back panel to the top of the cabinet by prying them out from the front with a large screwdriver. (Probably the most difficult part of the job.)
6. Use a socket or nut driver to remove the two screws that hold the valve to the back panel.
7. Lift the cabinet from the bottom rear and tilt the cabinet forward until you can access the valve.
8. Remove the wire harnesses from the hot and cold valves taking note of the wire orientation. (The red one will go back on the hot valve.)
9. Use pliers to open the hose retainer clip and slid the clip out of the way and remove the hose from the valve.
10. Reverse the process and you are done!

Two screws holding top, unhook wire conector. remove cabinet,replace switch. Reassemble.