1106603300 Kenmore Washer - Instructions

I knew I needed a faucet adapter, but thought I could just go to my local home depot and get the part...not so much. After 3 trips and not getting the part I truly needed I ordered the part from partselect. I received it literally the day after I ordered it, screwed in place with no tools, attached the coupler/hoses to the faucet and washed dishes. I wish I would have ordered the part from partselect before even bother with home depot. I would have saved myself a lot of trouble! Extremely happy! Thank you!

Replaced the faucet adapter, works fine

replaced the faucet adapter I did not save when I change out the kitchen sink faucet set

I'm a 66 year old lady with no repair experience at all!! I found the part I needed on Parts Select, which I ordered and received in less than 4 days. I watched the video that you've posted on your website which shows in great detail how to do this repair. It looked like a simple fix and it was!! I highly reccomend Parts Select!! Took my granddaughter(held flashlight) and myself less than 30 minutes to do the repair!!!

1)Shut off power supply to dryer. 2)Removed lint filter. 3)Removed two screws that secure filter duct to dryer top. 4)Lifted front of top to gain access to door switch. 5)Removed two switch mounting screws. 6)Removed the two power leads. 7)Reconnected power leads to new switch using "Normally Closed" terminal on switch. 8)Reversed the previous procedures to complete repair.

Removed the broken actuator and replaced with the new one. The time to replace the dryer door switch actuator took about 5 minutes.By the way, I purchased the dryer in 1965 and it works as if it was brand new. Thank you Kenmore for a lifetime dryer.

I followed the basic steps in the video for the dryer door switch replacement. My dryer is much older but everything in the video was basically the same. It was a very easy repair. I have kept this dryer running for 26 of the 27 years of our marriage.

Replaced actuator switch lever. Exact replacement. Worked like a charm.

I just remove two screws slip the old off and slip the new one on replace the two screws back put top of dry back in place replace two screws from dry lint trap

I am one Happy Gal.....Looked to fix,thought about just buying a new dryer..In the end talked to the local repair guy...said I could do it myself. (why pay him)..I live in small town.Ordered your part,watched the video and did it...Saved myself over $500, plus the $125 for delivery.for that new dryer..(Small town in the forest!)Very easy to install....Hope to use this dryer for many months perhaps years..It is 30 years old! Works like a champ! Thank You!

Located broken front door safety switch actuator. Ordered new part shown on the diagram. Removed broken part, installed new part, start dryer,runs fine.

My wife did the repair. Went on your website and watch the video on how to replace the switch and she was able to do it herself. I didn't mind at all. Saved $75.00 service charge.

removed 4 screws. 2 in the back and 2 at the lint screen door. Remove top lid of dryer and looked down and there was the door switch with the broken actuator spring. A diagram of the dryer with part locations is very helpful. I checked the switch with volt meter to make sure it was ok. It was ok! Replace the actuator and put every thing back together and dryer works just fine. Thanks to PartSelect I was able to buy the actuator spring buy itself and not have to buy the switch also.

1) Using a Phillips head screwdriver, the two screws retaining the hinge pin to the lid were removed. 2) Remove hinge pin and tilt lid slightly to gain access to bushing hole. 3)Install new bushing in hole. 4)Reposition lid. Insert hinge pin through lid and into bushing. 5)Reinstall hinge pin retaining screws and tighten.

After watching some on-line vids, I determined it was the center post, or tub, gasket at the bottom. A cheap part, and easy to snap-out the old and snap-in the new - But - I had to dissassemble the washer into individual washer component molecules. Luckily, I'd done this recently to replace the clutch drive, then the motor, then this. Not too bad, really. Washer body off (2 screws and two snap-links); agitator out (7/16" socket on extension); bang off tub nut (heavy hammer and punch); bang off drive block (hammer again); and pull tub up an out. Tub drain disconnected (pliers); pull off level sensing tube; three spring mounts (nutdriver); then just yank tub up. Poke out Centerpost gasket; snap in a new one; reassemble. Piece of cake.