1106004711 Kenmore Washer - Instructions

Sprayed wd40 - limescale - boiling water , NOTHING WORKED after half an hour reapeted spraying and pulling the tub and shaking it back and forth - still nothing
Finally I replaced the center nut loosely than putting a piece of wood on top of it and with me holding the tub slightly high - my wife than whacked it hard several times , I also was turning the tub every whack
When it came out it was full of rust and grime - it would have never come out without what we did
Replacing the the rubber washer was easy - machine works and no more leaking- thank you for your video which really helped to start the job

There are two screws that hold the switch in place. And two wires connected to the switch. The most difficult part of replacement is to place the new switch and hold it in place to reinstall the mounting screws. The space to work in is limited unless you remove the front panel from the dryer, which I opted not to do.

Did not hear the "clicking noise of the door switch when the dryer door was shut. First I unplugged the dryer from the socket. Next I removed the two screws that hold the lint filter receptacle. Next I pried the top of the dryer open with a screwdriver. Next I removed the two screws that held the switch actuator spring in place located just inside the top of the door. Then I removed the old spring from the door switch and replaced with the new. Not too difficult once the problem was diagnosed.

I disconnected the dryer from the electric. I removed the lid to the dryer by first removing the lint door screws and prying the lid off properly. Disconnected the wires to the door switch. Removed the screws from inside the door and carefully removed teh actuator. Seperated the actuator from the switch and replaced the broken actuator. Reinstalled the actuator and switch and screwed the assembly back in place. Reconnected the wires, lowered the dryer lid and screwed the lint door screws back in place. It Worked perfectly.

You can buy the switch AND lever/latch, but partselect had lever by itself which is all I needed. Pay attention to orienation of lever around switch when you take old latch off and attach new. Also, be careful to not drop new lever behind/beneath clothes dryer drum. Took my wife and I a while to fish it out. I have replaced heating element, and other parts. At some point it will be time for a new dryer...

First used wet vac to get water out. Unplug electrical cord. Shut off water and unhook lines. Unhook drain tube. Flip over on side. Take belt cover off. two screws.
Took photos of parts removing just for re- install. Ordered parts from part select.com. Came in Two days. The dealer was on 12 days I gave up on them. I removed actuator two easy screws and pulled off electrical connection no tool needed. Then removed pump three longer screws Than other part. Make sure to label them in a ziplock baggie. Plus I removed hose clamp with pliers slide Back on hose and pull hose off. Then remove electrical connection on pump. If it makes you feel better label each with masking tape so I know where each connection goes. Then replace pump first with new one. Make sure you push it in hard then the screws. Don’t over tighten. Plastic parts break. Hook back up hose slide clamp back over fitting end with pliers. Hook up wire connector. Next hook up actuator. Two screws wire connector and your done. Put belt guard back on. Socks can get caught under washer get in belt and cause major issue. Then you need to reconnect water lines. Make sure hot goes to hot. Cold to cold. Drain hose hook back up. Plug in power cord. Now the fun part. Run a diagnostic and then calibration. See you tube videos it’s like 3 clicks to left then two to right with selector knob. Write down the exact amount of clicks and steps. It works. Be sure to turn knob 4 times to left to clear it like a combination lock. Don’t let the noises scare you it makes all
Kinds of sounds while calibration goes on.

It was fairly easy a few tight spaces to reach in but all in all it was pretty straight forward

To replace the light bulb, I removed the screw and the cover, unscrewed the old bulb, replaced with the new bulb and replaced the cover, securing it with the small screw. It worked appropriately with normal use for a few days and then I noticed the light was not coming on when I opened the door.

I removed the cover and pulled out the bulb to find that the filaments inside are dangling and burned through. I need them replaced, please.

Before beginning, unplugged dryer. 1) Used putty knife at each front corner of top to pop lid loose from clips. 2) Removed hex screws at back of control panel to allow lid to tip open. 3) With lid opened, removed hex screw from inside-top of each side to allow front to pull open from side panels and access door switch easily. 4) Removed clip that holds retaining wires from top. 5) Pulled wire from each side of door switch. 6) Removed switch assembly using Phillips screwdriver to remove two screws mounting switch at top of door opening. 7) Removed broken actuator spring and replaced. 8) Reversed process to reassemble.

My dryer is 35 years old and thought this was it, but I googled the question and found out it was the door switch. Orderd the part and received it very fast and didn't want to wait for my husband to come home so I went on you tube and found a video how to open dryer and change switch. I did it in about 30 min. and yes it is now perfect again. No problems. I just unscrewed the old switch and put the new one in. Maybe I'll get another 35 years out of this machine. :o) Thanks for making it so easy.

replaced missing screw and pad and now machine works perfectly

Disconnect dryer.
Unscrew the two screws that hold the door actuator assemby.
replace broken spring.
Screw the the two screws back.

This was rather easy to fix. I had never opened the dryer before but had a serviceman come out so I knew that you can pop the top of the dryer off by putting a flat edge screwdriver in between the top and bottom and popping up. You must remove the screws from the lint dryer before so the top comes off. The piece to replace had two screws and that was it. To get a repairmen from Sxxrs where we purchased it 15 years ago they charge a flat fee of $75 just to come out. That does not include the repair just a fee to come and tell you how much more it would cost to fix it. I ordered the part for less than $5 and $12 more for 2-3 day delivery! What a bargin! I was back drying clothes 15 minutes after the part arrived! Very happy that the part is still being made!

Two screws holding top, unhook wire conector. remove cabinet,replace switch. Reassemble.

Unfortunately after i replaced the new switch the drier worked well. After it stopped for the 2nd time we wanted to put a load and start the swit lost contact. It was not working.It lost the contact with the circuit. No clicking sound the drier not functional. I guess need a new switch?