11081476430 Kenmore Washer - Instructions

Opening the washing machine, and removal and replacement of the water inlet valve were both trivially easy. However, getting the cabinet back into place was a bit tricky, only because I did it by myself. It was surprising how flexible and flippy-floppy the cabinet became when free of the structure of the machine. It would have been a huge help to have had a buddy over to just help place the back corners of the cabinet into place. That would have made the whole job totally easy.

Unplugged the washer and pulled out from wall as far as hoses would permit. Removed and drained both supply hoses. Removed drain hose and drained. Any water left in the tub will drain here so it's best to make sure it's drained prior to repair. Used pliers to hold the hose clamp and removed. Took screws out of drain hose interface plate and pulled out far enough to disconnect it from the internal hose.
Removed the two front screws of the control console. removed the two top hinge screws on the back. Removed four screws at the bottom of the rear access panel. Had to lift unclip several clamps holding the level hose in the control console and a cable connector. Unclipped various clips in the back panel to free it from wire bundle and such. Lifted the back panel up off of the clips located at the rear base of the control panel.

Removed two screws to free the solenoid assembly from the back panel. Unplugged the connectors to the original solenoid assembly. Disconnected the internal hose from it. Installed screw and plate supplied with the replacement solenoid to configure it with the same orientation as the original. Connected the internal hose and electrical connectors. Reassembled the back in reverse order as diassembled.

removed the two screw that hold the inlet valve take hose of .the first was takeing the back of than the hoses from back hose on bottom of machine.

Removed backing and hoses and replaced the water inlet valve.

I notice a screetching sound started and as time went on the water that flowed out to fill water drum was not working properly, unplugged washing machine electrical cord from outlet. disconnected water hoses, removed screws from control panel, pulled out front cover off wachine machine to access water valve, removed by unscrewing 2 screws, placed bracket on new part(placed over valve and pushed bracket up to slide and align srew to tightenbracket), put everything back in reverse order, helpfull video on video web site for visual

I followed the great step by step video instructions that you provided. The only difficulty was getting the plugs off the Water Inlet Valve. I had to use pliers (gently) to pull the two plugs off. I would highly recommend PartSelect to my friends.

looked on the find a part by s symptom. found the part,moved the washer took off the back.took 2 screws off of the top of the machine/controls.lifted the top.replace the water inlet valve.put it back together.easy repair.

I simply watched the video that PartSelect has online and it was a big help although my washer was a little different it still gave me the general idea on how to remove the casing. Great website! Thanks PartSelect!

Take top of washing machine off. Turn spikets off and remove hot and cold inlet hoses. Remove one screw holding part in place. Reach from front and take valve out. Unplug wiring harnesses. Reinstall the same way I took it off.

As I tore my ACL, my wife actually did the actual repair while I talked her through it. The video on your website was such a great help. Our repair went exactly as depicted.

replaced valve. Everything now working. Ordering the part was simple and I found a how to video on line that was great The whole replacement of the defective part was easy and the machine was back on line in 30 minutes.

easy repair and so far so good stopped over filling so far hope this helps ... scott

i removed all screws for back of washer and removed top washer controls. then removed the valves and replaced with new one. reinstalled back in reverse order.really easy job. you just have to pay attention how you took it apart and study how it works , thanks!

I removed the faulty valve after unplugging the AC cord. Two screws, the two water hoses were removed, and the electrical connections were unplugged. The old valve could then be rotated so that the clamp on the fill tube could be loosened and the tube pulled off the valve.
The new valve body seemed to be an exact replacement, but the mounting bracked was slightly different and required drilling two new screw-mounting holes; an easy job.
Before securing the mounting plate to the machine, the fill tube and clamp were reattached, and the electrical connectors plugged in. After connecting the supply hoses and plugging in the AC cord, the machine filled with water properly and everything seemed to be back to normal.
I might have been able to use the original mounting plate, but it had been taken to a different location which was too far away to easily retrieve.

I just followed the instructions from a previous customer. Worked perfectly.