11074414840 Kenmore Washer - Instructions

First I unscrewed two screws holding the back panel. Unscrewed the screws holding the water valve onto the back panel. With a screwdriver, pried the panel out far enough to pull the old water inlet valve out. Remove the connections on the old valve and replace with the new one. Screw everything back together. Fairly easy repair. Cold water flows like new and the noise is gone. Hope to get another few years out of the washer for this $25 fix.

Followed the instructions. Removed two screws on front panel, flipped it up and popped up the retainer clips. Tipped the washer body forward. Unscrewed the old valve and replaced with the new. Reversed the previous procedures and put the whole thing back together. I had put up with this low flowing water for a couple years. Now it fills like new!

Removed two screws holding top control section on, and folded back the control panel. Removed two clips holding cabinet on, tipped cabinet toward me and off. Removed and replaced water valve, being careful to mark hot/cold hoses, and secure the internal hose to the valve with the spring clamp. Most difficult part was lining back up the cabinet when putting it back on the base, but a few minutes to line up tabs and get the front of the cabinet UNDER the front groove in the base got it secure. Works fine now.

1. Unplug washer, close hot and cold water supplies and remove water hoses from washer inlet valve.
2. Remove two screws at the bottom of the front of the control panel.
3 Remove two screws at the top of the back side of the control panel.
4. Remove control panel.
5. Remove two retainer clips that hold the back panel to the top of the cabinet by prying them out from the front with a large screwdriver. (Probably the most difficult part of the job.)
6. Use a socket or nut driver to remove the two screws that hold the valve to the back panel.
7. Lift the cabinet from the bottom rear and tilt the cabinet forward until you can access the valve.
8. Remove the wire harnesses from the hot and cold valves taking note of the wire orientation. (The red one will go back on the hot valve.)
9. Use pliers to open the hose retainer clip and slid the clip out of the way and remove the hose from the valve.
10. Reverse the process and you are done!

The replacement of the water inlet valve was not too difficult after reading the steps posted by others. The main step is to unscrew the top control panel first, remove the top 2 screws of the back panel, and you have easy access to the water inlet valve. No need to remove the entire back panel. Follow the instructions which accompany the replacement water inlet valve and you should have no problems. The washing machine now fills faster with the replaced water inlet valve. The replacement inlet valve arrived within 2 days of ordering! Thanks for the superfast shipment!

My dryer is 35 years old and thought this was it, but I googled the question and found out it was the door switch. Orderd the part and received it very fast and didn't want to wait for my husband to come home so I went on you tube and found a video how to open dryer and change switch. I did it in about 30 min. and yes it is now perfect again. No problems. I just unscrewed the old switch and put the new one in. Maybe I'll get another 35 years out of this machine. :o) Thanks for making it so easy.

Two screws holding top, unhook wire conector. remove cabinet,replace switch. Reassemble.

It was fairly easy a few tight spaces to reach in but all in all it was pretty straight forward

Initially, we thought the problem was in the water inlet valve and we changed it out. It went OK although the Kenmore almost fell apart after the removal of a few screws and the control unit.
Only thing was that it was unncessary. The real problem was not in the cold water turn on valve, but in the hose. The hose was special in that it was designed to shut off under emergency conditions. It appeared to be able to passs water when tested at my sink, but when connected to the washing machine and under presssure, it would not pass water. I had installed the part by this time so I left it there. I found the Kenmore washing machine rather flimsy in it's construction and tended to totally come apart once a few screws were removed.

unscrewed the back removd thr two screws for the element unhooked the hose to machiine unpluged the electric to element and than replaced new element and plugged electric to element and hooked back the hose and replaced screws too the back and replaced back an screws
titled wash machine up hooked hoses for the water and plugged electric and put drain hose back to drain done

The valve was easy to change, but we as homeowners should change the hot and cold hoses just like they say you should every 5 years. The hoses grew to the water valve and it was almost a disaster. After cutting the end with a dremmel and clamping visegrips on it I finally got it loose. After that it went smooth. Thanks for getting me the part so fast.

1- Unplugged washer. 2- Turned off water supply to hoses hot and cold. (marked hoses H C) 3- Unscrewed hoses to washer. 4-Used phillips head screw driver to take out screws(2) at corners of washer. 5- Slid top of washer forward and lifted top off. 6- Took out retaining clips on each side of washer. 7- Slid frame of washer outward exposing rear panel of washer for access to water inlet valve. 8- Used 1/4" drive to take out screw to inlet valve. 9- Removed inlet valve, unplugged the two connectors and removed clamp from hose to valve. 10- Replaced new inlet valve and reversed the process to assemble washer back together. Total time for repair, about 45 minutes. I now have full running cold water to washer. Thanks guys for the video you provided. Would purchase again if needed. Thanks again!!! Water Inlet Valve with Mounting Bracket Part Number: PS334646

Followed by installation on line

I got a few hints from YouTube (how to remove the washing machine casing) and rest was very simple

received valve as ordered a simple installation. everything went well.home owner can do this repair