11082994310 Kenmore Washer - Instructions

I followed the online instructions to remove the shell and attempted to remove the drum, but not having the special wrench to remove the special nut, tried using a screwdriver and hammer, which failed to loosen the nut. I then started examining the the undercarriage and saw that I could replace the springs without removing the tub and did that. In the course of replacing the springs I discovered I could also access the wear pads by lifting the drum off of the undercarriage and placing a block to hold it above the pads. I was able to pop the old pads out by tapping underneath them with a hammer. The new pads were then installed and the weight of the drum popped them in. It was necessary to lift the drum assembly three times for each of the three pads.

Unplugged the appliance. turned off inlet water and removed hoses. popped the cap off hiding the bolt that keeps the agitator in place and pulled the agitator off. tipped the washer on its front . disconnected the Wire harness. removed the 3 bolts that hold the pump, motor,clutch, (drive assembly in other words). pulled the Drive assembly out of its resting spot removed the bad clutch and replaced it with the new one. then reassembled in reverse order.

First, I wrestled off the top cap of the agitator. Then, I unscrewed the bolt and took out the cam. I noticed that the agitator dogs were worn smooth. I replaced them, put it all back together and VOILA! I bought the whole agitator kit, not knowing what I was going to find, because I wasn't a Magtag repair woman. It ended up that the cam that came in the kit was too big for my washer anyway. Luckily, all I needed was 4 plastic dogs. The price of the whole kit was so inexpensive anyway, it was no big deal. Especially because, I was looking to buy a new washer or a big repair bill. This website is great! Thank you.

Tilt machine on its side,snap off the two retaining straps and remove the pump and sanded the shaft on the electric drive motor to remove rust ,Install new pump and retaining straps and unit now running great.

placed washer on side and installed new pads
and returned washer upright

Took the agitator out and gearbox off unhook wires from motor and take off water pump, replaced the parts and put back together. Pretty easy to fix. However, I still haven't got my problem fixed. Originally the washer wouldn't spin after the rinse. I put on a new coupler and it worked for a few loads, then something smelled hot and started stinkin the house up so I opened the washer lid and smoke rolled out. Turned it off. Took the moter off and checked it and it would barely turn at all. Replaced the motor with a new one. Still wouldn't spin. Put on a new clutch assembly. Still wouldn't spin. Bought a new capacitor thinking that would do it. Still don't SPIN!!! (The ring and washer I replaced was just a casualty, not any of the problem).

Completely dismantled washer per video , replaced gasket and spanner nut, then re-assembled washer. I’m a 58 year old female. It was tough. Main issue was that video was for dif. Model washer. Had to figure out some things myself.

Once I finally found the part I needed, the repair was very simple and took only a few minutes. Thanks to the very helpful operator to walk me through the diagram to find the corresponding number for the part. I really appreciate your help!

!. Removed agitator from inside
2.Removed outside cabinet
3 Removed pump, motor, and transmission.
4. Slid the entire drive unit out of the tub from the bottom
5. Removed the clutch assy. and installed new.
6. Reverseed the procedure to re-assemble.

3 online people recommended tilting the machine on the side and replacing the 3 suspension springs. Someone else recommended changing the tub pads. That is the wrong approach. It is actually easier to remove the case than turn the machine on the side. Once you do it once or twice it takes less than 2 minutes and it doesn't distort the suspension. You don't even have to disconnect the hoses. When I originally examined the machine lying on it's side I saw that the tub balance spring was still attached to the tub but the other end had detached. I looked for the place to reattach it. I found a place on the glide plate. Unfortunately this was the wrong place and the machine continued to bang away. When I realized that the spring had to be attached to the lower frame rather than the glide plate (one week of looking). I even wrote to the Repair guru. Once I found my mistake the repair took 5 minutes and no tools other than the phillips screwdriver to take out the 2 screws for the case. I replaced the tub balancing spring for good measure. The machine works great.

Basically I followed the great instructions provided on the Part Select webpages. I would consider myself to have more common sense than mechanical skill. I didn't want to have to keep going back to purchase more parts so I decided to buy the motor coupler (under $5), new clutch assembly (Under $30), new motor (under $160). The shaft on the original motor wore down to a cylindrical shape which should have been more of a rectangular shape to fit precisely into the motor coupler and provide the grip strength for the washer tub to spin. Usually the no spin problem is linked to a faulty motor coupler. I was glad that I had to removed the motor to reach the motor coupler because in my case the coupler had not failed. That is when I saw the motor shaft had worn. Since I had all the new parts I replaced them all and since 6/13/19 the washer is running like new. Oh, the problem was most likely caused by someone in my family "overloading" the wash machine one too many times over 11 years. Guy's / Gal's you can do this and save yourself from buying a new washer for between $850 - $1,200. My repair expense was under $240 including tax and next day delivery of my parts. Thanks Part Select !!!! Neil

We ordered both the motor coupling and the clutch assembly based on our troubleshooting, and because we figured both parts were inexpensive enough we might as well have them both. We initially thought it was the clutch assembly, but as we were taking the washing machine apart, we noticed that actually one of the bolts was missing completely and one had snapped in two. We then realized that the spin cycle problem was actually related to the instability of the motor because of the missing/broken bolts (they didn't even have washers!). All we had to do was replace the bolts and use a bolt extractor to get the broken bolt out, but we went ahead and replaced the clutch assembly as well for good measure. Everything ran perfectly after that! I was very skeptical to do the repair myself, but it really is easy, as long as you have someone with muscle to help out. You can also look up videos online that show you a step by step repair process for the clutch assembly, and I would highly recommend doing that so that you have a visual. It will make everything seem 100x easier.

Followed the excellent video instructions. They say you can perform the repair without removing the enclosure, but when I saw how easy it was to remove it, it definitely improves the access and speeds the repair. Have a piece of wire handy to to hold the pump assembly out of the way. Installed new clutch kit and it runs like a champ.

Pop off the softener dispenser. Pull the cover/ seal out of the upper agitator. With 7/16" socket and extesion bar, remove bolt and pull upper agitator straight up and off. dump out old assembly and replace with new assembly. Set back in place and replace bolt. Repair kit comes with good instructions and new rubber O ring for bolt cover/ seal. (thanks).
The suspension spring takes more effort but not hard. with washer laying on face I used a piece of 2x4 to pick up the tub in the direction of the broken spring. Put the new spring through the wire hook loop and snake it through the slot in the frame and you can see how it locks in place. With the 2x4, push the tub toward the new spring until you can hook it through the slot on the tub frame. Done. Parts cost less than an estimate from a service call and I finished the job in 30 minutes, which includes unplugging the power cord, turning off the water and taking off the hoses so I could lay the washer down. Saved the website in my favorites for the same great prices and fast shipping next time.

Repair went well, but my switch only had one contact on the non common end. The new switch had two contacts. One is for operation with lid open and one for lid closed. Make sure to connect to the lid closed contact and the common on the other end and leave the lid open contact unused.