79641473210 Kenmore Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- MARY from ANDERSON, IN
- Parts Used:
- EBF49827801
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Alarms about "Door Open"
Just removed the top cover only. Reached down and unplugged the door switch. Then removed the switch with 2 phillips head screws. Replaced with new switch. Reached down and plugged that new switch in. Problem solved!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jason from S HAMILTON, MA
- Parts Used:
- 4738ER1004B
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Leak in top washer hose
Super straightforward to diagnose and repair.
There was puddle under the washer.
I removed the top (screws in rear, slide top toward rear slightly and lift) and followed the trail of water up to the top washer hose between the drum and detergent tray.
Two hose clamps to remove and replace, then replace the top and ready to go.
There was puddle under the washer.
I removed the top (screws in rear, slide top toward rear slightly and lift) and followed the trail of water up to the top washer hose between the drum and detergent tray.
Two hose clamps to remove and replace, then replace the top and ready to go.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tom from BETHEL PARK, PA
- Parts Used:
- EBF49827801
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Washer wouldn't start when I closed the door. Door lock error code presented
Took the sealing ring off the gasket, unscrewed the door lock with two screws. Unplugged it. Plugged the new one in, screwed it back in. Put the ring back on and it started right up.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from SAINT CHARLES, IL
- Parts Used:
- 4738ER1004B
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Leaking hose
2 hose clamps and a hose, easy! This would be a very common cause of leaks in washers due to all the movement inside.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gloria D. from MEMPHIS, TN
- Parts Used:
- AGM73610701
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
broken retainer
pops right into hole
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from EATON, CO
- Parts Used:
- EBF49827801
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Door Lock Switch Replacement
The video from PartSelect showed removing the retaining ring from the rubber washer tub boot to then allow access the door lock located behind the boot for replacement. That ring can sometimes be a real pain to put back on. This can be avoided altogether!
It's much easier to access the door lock switch by removing the two retaining screws on the top cover of the washer found in the back of the machine. Remove the top cover and you can then reach down to remove the wiring connector, unscrew the two phillips screws on the front of the door latch and remove the door lock. Put the new switch on in reverse order; plug in the connector, replace all screws and the top cover, and you are done! This method took than 10 minutes from start to finish.
Please note that the washer should be unplugged from power while working on any electrical component.
It's much easier to access the door lock switch by removing the two retaining screws on the top cover of the washer found in the back of the machine. Remove the top cover and you can then reach down to remove the wiring connector, unscrew the two phillips screws on the front of the door latch and remove the door lock. Put the new switch on in reverse order; plug in the connector, replace all screws and the top cover, and you are done! This method took than 10 minutes from start to finish.
Please note that the washer should be unplugged from power while working on any electrical component.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barry from WAUSAU, WI
- Parts Used:
- EBF49827801
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
replace door locking mechanism
remove 2 screws from top panel - pull top panel back and lift off washer. reach down on front side and remove wire harness that is attached to door lock assembly. remove the 2 screws on front of door lock,remove and replace with new assembly. attach wire harness and then tighten assembly with the 2 screws. replace top of washer panel and tighten with 2 screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from FENTON, MO
- Parts Used:
- EBF49827801
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The locking mechanism had a fault and would not lock so the washer continually posted the locking error
Followed the video supplied by this site and everything was as described!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anne from MONROE, NY
- Parts Used:
- AGM73610701
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Magnetic door plunger broke off, then got stuck inside the door and couldn't be removed for replacement.
I used another magnet to pull the old plunger out of the door and replaced it with the new part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from IOWA PARK, TX
- Parts Used:
- AGM73610701
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Door plunger had a broken tooth and would not stay in place.
Just put in the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Andrew from BOTHELL, WA
- Parts Used:
- AEG33121501
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
TE error. Replaced heater / thermistor assembly.
removed top and front. heater is at the base of the tub. the nut compresses the rubber seal and may take some wiggling to remove the old one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- lawrence from DOBBS FERRY, NY
- Parts Used:
- 4681EA2001T
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Water wouldn't drain
I followed the video. Everything worked exactly as described. i ran a quick cycle and everything seemed to be fine. Started a wash and the machine was going fine but stopped, and wouldn't drain. I thought that maybe it might be the Rotor Position Sensor assembly, which I had already purchased just in case.But first i drained the machine and checked out the pump filter. Plugged solid. I'm guessing when the pump went there must have been a lot of lint and debris in the machine. something you might want to check out, after that repair. Thanks. you guys saved me a couple of hundred dollars
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- paul from DELAND, FL
- Parts Used:
- EBF49827801
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
door lock malfunction
ridiculously easy. removed the door gasket ring clamp. separated the gasket from the face. unscrewed the lock, removed the wire(gently). replaced the wire on the new lock. replaced the lock. replaced door gasket and ring clamp. washed clothes. Note- I had called a repair service and was given a $360 estimate in addition to the $130 dollar service charge. All total- $50 dollar part(with shipping), less than 45 min total time and I'm no mechanic!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jesse from CARNEGIE, PA
- Parts Used:
- 5220FR2006H
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Dishwasher would not fill
Used Youtube to look for a set of repair instructions. From start to end 35 min.
The difficult part was getting the door back on. Only 1 Youtube video I watched stated Do not remove the 2 center screws at the top. Wish I had seen that video first.
Overall very easy to do.
The difficult part was getting the door back on. Only 1 Youtube video I watched stated Do not remove the 2 center screws at the top. Wish I had seen that video first.
Overall very easy to do.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gregory from PITTSBURGH, PA
- Parts Used:
- 4681EA2001T
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Drain pump inoperable
1 tilt washer back
2 remove cover plate screw from front of drain filter access panel.
3 Remove cover plate and remove 2 more mounting screws .
4 go below washer and pull down sliding clip and move pump assembly back.
5 remove wires and 3 mounting screws around pump housing
6 Swap pump and re-attch wires
2 remove cover plate screw from front of drain filter access panel.
3 Remove cover plate and remove 2 more mounting screws .
4 go below washer and pull down sliding clip and move pump assembly back.
5 remove wires and 3 mounting screws around pump housing
6 Swap pump and re-attch wires
Was this instruction helpful to you?
Thank you for voting!