A300 Jenn-Air Washer - Instructions

Observed source of leak by lying on floor behind washing machine and placing hand in likely spots. Found water injector hose was source. Searched web for instructions to open up washing machine: 2 screws at bottom of front panel, then 2 screws at top inside after removing front panel. Easy after that. Lots of rust and rusty screws and rusty tinnerman nuts; had to grind off one of the screws with dremel tool.

Received wrong springs for my model had too use combo old spring with the two new (too long) springs to get the tension on the belts. For now it working. Did not contact you due shipping took so long and two delay date change by FedEx ground. I didn't want to go thru another delivery nightmare. Thanks for the time.

I first removed the front panel of the washer and removed 2 screws holding the top of washer in place. I had to flip the top up. This allowed easy access to the tub. I then removed the agitator by removing the set screw on the lower portion. From there I loosened the mounting securing device by using the nail punch and hammer inside of the tub (it was loosened by turning it clockwise). The tub was now loose and I removed it from the washer. Next I removed the torx set screw and the tapered hub unit (cork on it). It had to be again loosened with the hammer and nail punch and turning it clockwise. This exposed the part that needed to be replaced. I replaced the old with the new and the washer now works great with no leaks! Be sure to clean everything you remove that will be reassembled.

Unhooked water and drain lines, Unplugged electrical. Removed the two phillips screws at the bottom of the front cover. Removed the Front cover. TIpped machine backwards at about a 45 degree angle using a 2x4 to support the machine. Removed the pump belt and the drive belt. Installed the old pump belt and the new drive belt. Loosened the 3 each 5/16" bolts holding the pump mechanism and moved pump to the left. Moved pump to right to tighten pump belt and tightened the left pump bolt. Loosend the one pump bolt and pulled the motor to the left to tighten the drive belt and holding in this position I tightened the pump screws, Pump belt was now looser than the drive belt. Ran washer and it worked perfectly.

Tilt the washer sideways. Remove belts,Remove front panel, loosen two hoses, loosen three small nuts. Take out old pump and install new new pump vise versa. Video provided by partselect very helpful.

After looking up the problem on the PartSelect website, which indicated the problem could be with the tumbler (drum) belt, I watched the instructional video, which was very helpful, as the dryer in the video was exactly the same as mine. After removing the power cord from the wall and separating the exhaust vent pipes from the dryer, I followed the instructions for removing the front panel, the front bulkhead, the drum and the old belt, which was worn and somewhat stretched. I then followed the instructions for installing the new belt, but I found it was easier for me to remove the back access panel in order to complete the installation of the belt around the drive pulley and tension pulley wheels as I wanted to see what I was doing as opposed to just "feeling" the belt to ensure a proper installation (e.g., new belt not twisted). Once I removed the drum, and before I put in the new belt, I also took the opportunity to use my shop vacuum (and you really need a shop vac for its power)to remove 25 years of rubber dust from the old belt, house dust, and packed lint from inside the exhaust fan, cabinet, and the vent pipes (and a dead field mouse that had crawled into the dryer through the outside vent pipe and had gotten trapped in the exhaust fan). I also examined the heater tubes to insure no lint was inside that and spun the fan blades by hand to make sure the motor shaft was not worn. Once I was satisfied that the installation of the belt was done properly, I put the drum back on, reinstalled the front bulkhead (checking to make sure the felt gaskets were in place, as recommended in the video) and reattached the front panel. I also took the opportunity to touch up the accumulated minor nicks and scratches ion the cabinet with refrigerator enamel. Now that the new belt is on, the dryer no longer vibrates, and with the dust, lint and mouse removed, dryer is operating much more efficiently. Remember to re-balance the dryer using a carpenter's level to minimize any latent vibration. Note that the actual removal and replacement of the belt took me about 30 minutes, and the rest of the cleaning, reattaching of the vent pipes, and balancing, etc. took about two hours.

Frist take off front of the washer, removed old belts and then put on the new. very easy.

The PartSelect video was awesome in giving me confidence. The step by step instructions worked well until....

Calcium carbonate buildup on the reverse threaded spanner nut locked it in place such that I couldn't break it free.

I tried muratic (hydrochloric) acid which removed the surface scale nicely. But, no impact on allowing the nut to be pounded free. I then used a dremmel drill bit to vertically drill holes into the nut cross section. This allowed me to tap in a cold chisel and then pry the nut apart. Unfortunately, I had to repeat this for the second spanner nut as well.

Note, the first nut threads on the second part of the tub seal kit. So, drill away. You will not need these threads. however, the second set of threads you need to be carefull not to mess up. By drilling verically you can remove most of the cross section and cold chisel the rest without damaging the shaft threads. Second note: gently tap /wedge the cold chisel into your drilled out area. you don't want to hit hard and risk the ball bearings/raceway from getting ruined. Use the cold chisel to pry apart the aluminum stem hub. Its cast, so it will break pretty easily.

Net, the video allowed me to complete a project that exploded views, etc. would never have! The frozen nuts aside, this was an easy job that WORKED! No more leaks.

My 13yr old son and I fixed the washer in about 5 minutes. It was very simple and easy to repair considering I had never done it before.

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

I viewed and followed the PartSelect Instruction Video. My only problem was reattaching the door after the hinges fell off.Everything fell into place as the video indicated. After I regrouped I was able to put the hinges back and then I was able to reattach the side panel very easily as the vedio indicated. Thanks for everything.

put on the new belt. it also smelled like smoke when we first ran. upon further inspection, saw that the drum was not turning easily. felt around the top inside edge of the drum, found the real problem- there was a sock jammed on the top edge between the drum and rim. removing the sock was easy, and then everything worked great!

our neighbor had it done in no time!!!...

Being a single Mom with no mechanical background, it went very well. I followed the instructions which were very clear. I did it myself!

I followed the others directions and it's important to note that both nuts involed are indeed left handed threads. Also the it's important to know that[at least on my machine] that the set screw on the agitator is a torx headed set srew, not an allen srew. Other than that it was a pretty quick fix.