JW3000W Jenn-Air Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- rae from Los Alamos, NM
- Parts Used:
- WP35-6465
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Wrench set
Washer was noisier than usual, after a while could smell something getting hot, and then the machine stopped working. After a while it would start again but not for long.
I had some expert advise on what the problem was so that made it easier to consentrate on the fix. I was surprised to find so much information on this web page. Getting the right part ordered was also very easy. The repair instructions given by other people was all correct, tiling the machine to get the belt off, removing the back access panel, was all correct and made it easy. The hard part was getting the machine out of the small wash room and into the garage where I had room to work on it. A good dolly and a wooden ramp came in handy . A word of advice woud be to operate the hot & cold water faucets on & off every year or so to be sure they work easily when the time comes, maybe an emergency. After 12 years I was worried my valves would give me a problem. (.they didnt).
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Willie from Pensacola, FL
- Parts Used:
- 12002213
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Would not agitate
Followed video instructions. Most difficult part was re-installing the E-clip on the bearing.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dawn from Franklinton, NC
- Parts Used:
- WP21352320
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Washer would not agitate
Tilt washer back to expose the bottom. Remove broken belt. Install new one. Do a test run: Washer is back to working fine. Note: My boyfriend actually did the repair while I was at work, but reported that I could have done it myself easily. Also: FedEx delivered the part on a Saturday without an extra delivery charge, so my washer was repaired several days sooner than I anticipated. Thanks, PartSelect!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joshua from Barnsdall, OK
- Parts Used:
- WP21352320
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Burning rubber smell & noisy
Pulled the washer away from the wall, tilted it 45' pulled belt off loosened the bolt on the motor belt tensioner & installed new belt.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Valerie from Steger, IL
- Parts Used:
- WP21352320
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Drive Belt shredded and fell off.
The repair was very simple. We got the part faster than we thought we would had our son hold the washer on a tilt and put on the drive belt, took 2 times because it was twisted but we got on. The washer is much quieter and it was worth the shipping fee.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JASON from ARLINGTON, TX
- Parts Used:
- WP35-6465
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Drain pump pulley stared making sqeaking noise
turn off water to washer, disconnected hoses. Tilted over to open rear access panel removed old worn part replaced with new part reattached pulley. Replace access panel flipped back in operation position. Connected hose turned on water. Put small load in and turned on washer worked great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michlen from Kingsport, TN
- Parts Used:
- WP21002026
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Socket set
Washer jumping around during spin cycle
I used Utube to search for Performa Washing machine jumping around. You will find several videos that will be extreamly helpful in understanding exactly how to go about changing the sunbber ring. The snubber ring is fairly easy to change out. Quarters were used to hold the springs apart so they can be removed. Push the tub forward and away from the spring you want to remove. Install several quarters in the spring. Use as many as you can get in. Then pull the tub toward you and the spring can be removed from the tub. There are six springs to remove. I just left them laying in place at the bottom of the washing machine base. There are videos on utube also of using the quarters to remove the springs. Of course if you have spring removal tool for this purpose so much the better. I didn't have one. Good luck with your install. MB in TN
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tim from Ewing, MO
- Parts Used:
- WP35-6465
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
Washer wouldn't drain
I heard buziing and smelled a burning smell with my washer so i got on your website and watched a video how to take the washer apart and what the problems could be and determined it was the drainpump so i took the 3 bolts holding it on out and inspected the belt while i had it off , and ordered the part from you guys and put it on your information was very helpful
Was this instruction helpful to you?
Thank you for voting!