LAT7304AGE International Washer - Instructions

The machine had leaked late last year; replacing the interior hoses fixed it, but the leak came back.

To diagnose the problem, I used a short, #2 phillips screwdriver to remove the two retaining screws under the front panel indentation. I pivoted the front panel toward me, unhooked it from its retaining hangers, and set it aside.

Inspection revealed that water was running down the exhaust hose from the siphon break, so I unplugged the machine, pulled it away from the wall, removed the two top retaining screws and pulled the top toward me. There was enough play in the wiring harness to leave everything connected.

I used a socket wrench to loosen the hose clamp at the bottom of the siphon break, and to remove the 4 hex head screws that hold the siphon break to the back of the machine. A few twists freed the siphon break, and one glance revealed that its top was covered with soap scum. It clearly needed replacement, so I ordered the part.

Replacement was a piece of cake. I mounted the gasket in the new siphon break, moistened its tube, twisted it into the hose, and tightened the clamp with a socket wrench. I then mated the new part with the old exit elbow, lined up the holes, and installed the retaining screws. I pushed the top back into position, installed the top retaining screws with a socket mounted on a universal nut driver handle, rehung the front panel, and installed the two retaining screws. Presto, good as new!

Everything else is clean. I would much rather replace a few parts and continue using "Old Reliable" than pony up $800 on a new machine.

First I took the door off. Undid two screws that held the top door on. Took the tub out. Make sure you have a spanner wrench. So much easier.

Followed the first guys directions.
remove front
lift top
remove agitator
remove locking nut clockwise
remove inner tub
remove Mounting S loosen set screw and clockwise also
clean well
replace boot as shown in tip in sheet
push boot on completely

Unfortunately after i replaced the new switch the drier worked well. After it stopped for the 2nd time we wanted to put a load and start the swit lost contact. It was not working.It lost the contact with the circuit. No clicking sound the drier not functional. I guess need a new switch?

I took the front off the machine and ran the cycle to see when it was leaking. I found it was leaking when it was draining the water out on the inside of the machine where it was going out of the machine. I took that part out off the drain hose and ordered the part no that was stamped on the part. The part came in and I reassembled everything and it did not leak.

Raise the top off of the dryer with a flat blade screwdriver in each front corner of the dryer. Disconnect power to the dryer. Remove old switch and install new switch. Test door and proper operation of dryer.

Found the parts I needed on your website along with a video that showed exactly how to do the repair. Set my iPad on the dryer and followed along step by step. Never would have tried something like this without your helpful information.

Started with removing 4 screws on the top of the control panel. Once open, I found the schematic taped to the top. I traced the wires and found the 2 wires to test. I unplugged them and attached the jumper wire. Turn on machine and it worked. Ordered the part( it came in in about 3 days. First disconnect the power. The micro switch is mounted with 2 screws, remove these and as you disconnect the wires , attach them to the new switch, put it back in place and reattach the screws. Test .

First I took the seals out of the box they came in and let them hang on a hanger to get all the kinks out of them for a few days. Then I started at the corners of the refrigerator doors and peeled the old seals off on one door then replaced the seal by using my thumbs pushing at the corners first and once I had all four corners in I worked my way around the rest of the door, After both doors were done I used a hairdryer to expand the seals against the refrigerator case to make sure it seals tight.

Agitator motor burned out -- purchased new one through Parts Direct (parts still available) 4 bolts and plug and play wire harness and now runs like new.

First I bought a Maytag spanner wrench on eBay, you have to have it. It was $12.00 including shipping. Then when the parts showed up the next day followed the video and had it done in just under an hour from gathering my tools and cleaning up. The video was perfect and I had no troubles what so ever. The quote from the repair services was $280.00 and I did it for less than $90.00

I opend up the housing, found the broken part, ordered it, installed it, and had the washer working within 4 days of the initial break down.
Saved a lot of money over a service call, as well as time, and trips to the laundramat.

It was really quite simple. I found out where the leak was coming from by taking off the front panel and running the washer through the drain cycle. PartSelect website was right on for what part I needed and delivered it promptly. The installation video from PartSelect couldn't have been more clear. I removed a few screws from the back of the washer and installed the new part in about 1 hour. All was good.

Chalked the transmission with a pipe wrench. Removed the brake with grabbing on to it with vicegrips and hammered on the vicegrips to remove the brake. The new brake spun on after the first two brakes didn't. Working great now!

key to repair is to watch the video on mounting stem/tub seal as seen thru parts select. However, they use a nice new, clean,sanitized washer that may not reflect a 23 year old washer like mine. They give you the basics and it is invaluable to watch if you have never done this before. I strongly advise you buy a real spanner wrench made for your make. You may never need it again but it makes it much easier. Trying to use a punch or using a dremmel to operate on your large 'nuts' is, well, nuts! Get the wrench, just part of the cost of repair. See ebay. The first thing I noticed different between the video and my real life unit is the water hose connected to the washer, at the top of the tub cover. This did not exist in the video, but it is the way on my unit. So I did not disconnect it, just folded the top out of the way and tied it up. Then of course my real gripe with the video is that I have the old time band around the tub and the barrell, holding them together. They do not mate up very well and are not easy to put back together properly. In fact, installing the stem seals was easy and it fixed the original leak. I might add when you buy the replacement parts, you actually get 3 new parts. I suggest you use all the new parts in the package. You paid for them, you need them. Again the video only talks about replacing the very bottom seal, never mentioning the other parts they sold you in the bag. It is easy to figure out how to replace the other parts, they look like the ones you took off to get to the very bottom seal. Use all the new parts, regardless. So the only real issue is putting the band back on to hold the tub to the drum. We did not get it correct the first time and the unit would not spin, I had the top down too far. You could smell the rubber burning from the drive belt. They forgot to tell us about that!! Bums. So we loosened up the band, raised up the top piece and got it to spin. Of course, we did a large load, filled the water to the highest level allowed and when the unit hit the spin cycle, we got a leak from under the band. Thx video. To fix that we decided to never use the highest water level. So far so good. I can tell you the engineers failed on the design to mate up the cover to the tub. Other than that this can be done by us goobers, just take your time. And good luck. I must also thank my helper, neighbor John . for his added wisdom and support.