W236LKV International Washer - Instructions

I had my 12 year old son climb to the back and he took off all the screws necessary in the back and took the part completely off. We ordered the part and waited for it to come in. We replaced the part, the screws and honestly, the only thing we had trouble with was replacing the small cover where the hoses stick out of the washer. Was an easy efficient experience that may have saved me $300.00+ dollars. Thanks to my 12 year old son we got her fixed up. The washer works like brand new.

used putty knife to to raise the top, took out two screws, replaced parts , then closed the top.

Disconnected both power and hot and cold input water lines. Laid the washer on its front side for access to the bottom. Removed the small access panel from the back of the machine to remove the metal screws holding the pump in place. Removed the single drive belt. New pump installed easily, replaced the belt and access panel. Reconnected the power and water hoses and everything worked fine.

Changing the hinge was not difficult, but here's a hint: the top of the washer raises up if you pry it with a big screwdriver- be sure to wrap the screwdriver in a cloth so as not to scratch the appliance. Doing it this way makes it easy to access the retaining screws. You can push the wash tub to one side and reach the screws from underneath, but they're a tight fit and doing it that way is difficult. Overall a pretty easy repair and I'm only moderately handy.

first removed panel from rear of washer removed hoses and drained water in them, removed the 3 screws and removed the belt then removed the pump. Replaced with new one and put back screws,hoses and belt. walaaa.... it works like new!!!!

Removed access panel to expose pump, removed drive belt, and old pump, repeated the avove steps in reverse order, tested for leaks and proper operation.

I followed your video instructions. Very good video.

Removed water lines and drain, removed back panel, removed drain lines from pump. Unscrewed 3 screws to remove pump. attached drain lines to new pump, screwed in new pump, reattached everything. Reinstalled belt (very easy, not like an altenator). done

I pulled washer out and removed filler hoses from water supply and drain hose and tilted it forward placing three short 2X4's under the washer to keep it tilted forward. Removed
back plate with nutdriver. Removed belt from pulley and disconnected the two hoses from pump with pliers. Removed three large screws from pump base with nutdriver and removed old pump. Installed the new pump in reverse order. Quick and fairly easy took about 30 minutes.

tipped the washer back, laid on the floor, and wrapped new belt around 3 pulleys. everything works as before.

Tilted machine back, put a paint can under it and did R & R with belts.

First I got everything I needed, unplugged the washer. Using the puddy knife I freed the top of the washer by inserting the knife about four inches from each side on front. The machine is in a place where it can not be pulled out far, hence the two by fours. Remove the loose cover, reach in with the stubby and unscrew the screw on both sides. Take the broken cover pins off the cover and install the new ones, put the other hinges in the cover, put the hole cover in place and install the one screw perside, remove wood and close the hole top, your in business , no drinking

Removed screw, replaced hinge.

Replaced the hose. two clamps and retainers. very basic repair

Replacing a belt on a washing machine is a pretty easy process, depending slightly on how easy it is to access the belt. On our Maytag, the belt can be accessed directly underneith the washing machine. So, I lifted the front of the machine and put a few blocks of scrap wood under the legs to hold up the front of the machine. Once that was done, there was nothing else that needed to be removed to access the pullies that the belt had to go around. The motor itself is generally adjustable to allow the belt to be changed. So, I first wrapped the belt around the largest one that spins the washin machine tub, and then wrapped it around the one that spins the water pump. Finally, I loosened the bolt on the motor to allow it to move, wrapped the belt around the motor, pulled the motor back to tighten up the belt, and tightened the bolt that holds the motor in place. It's a pretty straight forward repair that narly anyone could do thmselves.