ITW4671EW1 Inglis Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Joseph from BAKER, FL
- Parts Used:
- WPW10006384, W10721967
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Loose pulley
Tightened up the pulley as the video showed me that might be the issue.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from OCALA, FL
- Parts Used:
- W10780045
- Difficulty Level:
- Difficult
- Total Repair Time:
- 30 - 60 mins
washer was shaking bad
Replaced the suspension rods not an easy task but very rewarding to hear it running quiet again when spinning.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- michael from BROOKLYN CTR, MN
- Parts Used:
- W10908289
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench set
Non agitation
It was so simple. The staff person recommended that I just YouTube it and recommended other options. As I said it was simple,
Everything I needed was in the box.
I removed the new part from the box.
I used the equipment needed to remove the top of the Agitator's bolt.
Removed the old part, clean the inside area.
Installed the new part which took some hard pushing down onto center piece and replaced the bolt in the casing.
Placed the top back on and done.
Everything I needed was in the box.
I removed the new part from the box.
I used the equipment needed to remove the top of the Agitator's bolt.
Removed the old part, clean the inside area.
Installed the new part which took some hard pushing down onto center piece and replaced the bolt in the casing.
Placed the top back on and done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leslie from ROCKY FORD, CO
- Parts Used:
- W11307244
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
The washer would not wash or spin.
I watched the instructions on line, and followed them. Completed the parts change with out any problems, but that wasn't everything I had to do to make the washer to work again. I had to clear all the fault codes that were on the machine. Then the washer started working in all the cycles.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from SAINT JOSEPH, MI
- Parts Used:
- W11210463
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Leaking water inlet valve assembly
Remove upper rear panel with drill driver and 1/4" nut driver bit. using the angle bit holder and torx bit remove the two screws holding the assembly in place. Slide out the old assembly and disconnect the wiring harness at the machine. Slide new assembly in place. While holding it down start both screws by hand, then use the driver/angle holder to tighten screws. Reattach the wiring harness and rear plate(s).
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from BELLEVUE, NE
- Parts Used:
- W10837741
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The Washer acted like the lid would not latch and stopped it from cycling.
My fault completely! I shut a valve off to a spicket that I have in my garage due to a Nebraska winter. The problem turned out to be that my washer was receiving its cold water from the line that I shut off. So it was an expensive lesson to learn after replacing the switch harness and the latch. Water was turned off Ding Dong!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bernard from ARIZONA CITY, AZ
- Parts Used:
- W10721967
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
Gear stripped on main spline
Followed detailed instructions which were supplied with the parts. It was easy and my machine is working great with no issues. Also I just didn’t get the main drive pulley, all new parts came for the bottom end, great service and excellent parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from GEORGETOWN, KY
- Parts Used:
- W10780045
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Socket set, Wrench (Adjustable)
Washer struts were wore out
Removed the old and replaced with new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JERRY W. from CARROLLTON, GA
- Parts Used:
- W10721967
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
making noise when starting spin cycle
Watch video on the site and the insulation will be easy and take about 30 min.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from MAHWAH, NJ
- Parts Used:
- WPW10006384
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Burning smell, ASSUMED it was the belt
Once we put the washer on it's side noticed lots of oil on the floor and in the belt cover area. Replaced belt anyway but issue is the leaking transmission. Starting warranty process since Maytag carries a 10-year part warranty and machine is 6.5 years old. Wish me luck !!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lucas from ARKANSAS CITY, KS
- Parts Used:
- W10721967
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench set
Making a loud noise for a while then stopped spinning
Removed two screws to remove guard. Two screws to remove another part with wires. Pulley nut was already missing. Component was twist locking tabs.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anna from TAWAS CITY, MI
- Parts Used:
- W10837741
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Lid strike broke
Removed old one (2 screws) slid in place and screwed in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jerry from LENGBY, MN
- Parts Used:
- W10913953
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
screeching noise at times,Wouldn't spin out
Tip washer on its front removed belt guard and belt. Removed shift actuator. Put new actuator on, put belt and guard back on, put back panels on and it was fixed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Cranford, NJ
- Parts Used:
- W10913953
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Washer would go from sense to done without running cycles. Sometimes the drum would make a quarter turn.
I followed the video published on this site
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kristy from Lebanon, NJ
- Parts Used:
- W10721967
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Washer was making an awful screeching noise when agitating
I turned off and disconnected the water lines (have a bucket ready) and tipped the washer on its back. I followed along with the provided video that was super helpful. Disconnecting, moving the washer, and reconnecting everything took longer than the repair. Very satisfied with this repair!
Was this instruction helpful to you?
Thank you for voting!