IFW7300WW02 Inglis Washer - Instructions

My dryer is on top my washer so I removed the dryer and pulled the washer out. I had to get rid of the water that was inside so I used my wet vacuum on the drain hose and sucked it out I then removed the front cover and the I tipped it back and removed two screws from the bottom of the pump bracket underneath the washer and moved the two clams on the pump hoses back to uncouple the hoses. I removed the pump and installed the new one and hocked everything back including the wires to the pump which is just a quick connect and pushed it back into place and it worked like new

the repair cost was about 1300$ from a repairman! and they wanted to replace the complete inside drum assembly, so i decided to break it down myself and i'm an average do it yourselfer 1. unplug machine 2. remove water hoses 3. remove the top 4. remove back panel and front complete 5. remove all inside connecting wires but leave them close as to make it easy to reconnect 6. take all three shocks loose from bottom of drum and remove all counter weights (concrete) 2 on front and 1 in back as to keed drum ballanced for removal and 7. remove the complete drum 8. set drum down door side down and remove pully and then all the metal clips with a flat screw driver and lift back portion of the outer drum up and remove. then the inner drum will be visable 9. take the 6 Torx (star) screws out of the drum support and remove! and semply reverse the process for assembly! taken photos of the process will help the assembly process as well

Removing and reassembling the front and top panels was very easy and straight forward. I started by opening the clean out next to the pump and to my surprise found 2 shiney pennies a rusted paper clip and a small nail. I inspected the bellows and found 2 - 1/4 inch slits near the drain holes in the bottom of the bellows, not big enough for the pennies to pass through so how did the pennies get there. Installing the clamp to the drum was fairly difficult. The hardest part of the bellow installation was getting the front spring clamp lined up and stretched. I used the old spring clamp, maybe a new one would halve been easier.I used some duct tape to hold the wire clamp in place and a screwdriver in one end of the spring and with a great deal of effort stretched the spring enough to get the clamp over the rim. I also sprayed some water on the groove in the bellow to get to seat on the rim

Took less than 5 minutes to replace, So Happy;-)

put in push down push back until they lock in

This part worked great! Completely fixed all the problems that I had with my washer. A bit hard to actually place it in(pliers are necessary) but otherwise very easy to install.

After unplugging the washer, the unit was pulled forward and tipped backwards, I placed a 2x4 under the washer to serve as a brace. I removed the existing bolts holding the old pump in place, removed the spring hose clams, unplugged the pump and removed the damaged part. inserted the new drain pump, re-inserted the bolts and tightened them, replaced the spring clamps with "regular" hose clamps supplied with the replacement part, plugged in the power supply, removed the brace, pushed back the unit and plugged it into the outlet. From start to finish - about 20 minutes. Was running wash about a half hour after I started.

I pulled the front load washer away from the wall and unplugged. I tilted it back against the wall. I removed three screws from the lower front cover plate of washer. Once removed, I had access to the tub to pump hose which I found a small hole in. I went online to Partselect and found my part. The hose was connected in three different places by compression clamps. I then pulled the compression clamps off the connections. Cleaned up all connection points with a damp rag. Upon installation of the new tub to pump hose, I discarded the compression clamps and installed the new part using radiator clamps purchased at a auto parts store. Plugged washer back in and started a load too make sure all connections were good and tight with no leaks. After checking for leaks, I re-installed the front cover plate. Tilted washer back down being careful not too set it down hard or on my feet. Job Done....

Very --simple remove front acess panel -- open sump clean out remove water out of existing pump an hoses with small wet dry vac -- remove small wire harnes --cut band clamp on discharge with side cutter --remove inlet -suction side of pump hose clamp with channel locks --un bolt two screws on bottom side of washer with 5/16 nut runner --discard old pump reinstall new one in reverse order --only takes about 20 mins total !!! ---

open the front bottom panel (3) screws. remove panel. twist off old shocks by turning the shock counter clockwise. reinstall shock by turning clockwise.

I was already very familiar with the motor & drain pump, as I had disassembled my original one in attempt to find the problem & fix it. Finally, I broke down & purchased a new one. It was VERY easy to install! The most difficulty was finding the right sized board to put underneath & raise the machine up (with the dryer attached to the top of it) to place the board underneath so that I could tighten the bolts from underneath to attach the pump. After that was over, the rest was cake! Just attach the hoses & the electrical, which just clips in place & my washer is like new again! Yay! Oh, and yes, I'm a woman DIY'er.

Followed instructions from a You Tube video. I'd recently lost my job and money is tight and I thought we could save money doing it myself. By watching the video and ordering parts from you we were able to save $500 between parts and labor. Thanks

other than needing a new type of screw driver (not philips or flat head, but rather a starfish looking thing), the replacement was simple. took 5 minutes (after finding the correct driver)

Replace water pump

Took of the panel, unscrewed the old drain, screwed the new drain in. Very very simple to do! The first part I received leaked, I called customer service and they gave me a refund and express shipped a new part - no questions asked. Very good customer service!