IP41002 Inglis Washer - Instructions

Followed the video instructions. Had no problems. The video was accurate.

Turn washer on its side unscrewed clamps used pliers to slide clamps off of two hoses connected to pump then took clips off that hold pump replaced with new pump and put new clips connected hoses and clamps on new pump turned it back upright job finished

diconnected water supply and discharge, unplugged the unit, removed the aggitator, laid the washer on it's back, romoved the hoses from the pump, took out 3 bolts, removed the motor/transmission and replaced the clutch and put it all back together.

Followed the video on the website. I removed the hoses from the pump rather than removing the pump as suggested in the video. Then separated the motor from the transmission and replaced the coupling; then reattached the motor and hoses. Lining up the washer cover and clamping it back on was the most trouble. But all in all, a easy repair.

I removed the back of the washer, removed the old water inlet syphon, replaced it with the new one, and, with some difficulty, replaced the back of the washer, reattaching all of the parts to it.

just like video showed really helpfull

After reading other comments about lid switch replacement , I knew the front of the control panel would move forward and lift off. Although none of the descriptions mention the steel clips that were also use to hold the cover down. It does take quite a bit of presure to pry these up and loose before panel would move forward. Would recomend putting tape on both washer and screwdriver to protect washer.

The water pump had a small leak when washing clothes, and my wife was nagging me about it. I know men, youwere shocked that I said nagging and wife in the same sentence. Me being a man, I would have just left it since it is in the laundry room in the carport.

I turned the washer on its side and felt where the leak was on the pump, went inside and ordered the new pump. It was here in 2 days and it took 15 mins to put it back on with only a screwdriver to snap off the retainers and pliers to undo two hoses.

I told my woman that it was fixed and we have lived happily ever after and we played Appliance Repair Man and I was paid very well for the "House Call" if you know what I mean!!!!!

I was familiar with the Kenmore / Whirlpool direct drive mechanism but at first I could not determine how to release the console. I finally found the end cap trim pieces would pop off revealing the 2 screws that hold the console in place. After removing them the console flips up and over the backboard. I then removed the 2 clips that hold the cabinet to the backboard, unpluged the lid switch connector and then tipped the entire cabinet forward and off the frame. This gives you access to the entire washing machine mechanism.
Next I released the 2 metal clips that hold the pump on and push it out of the way leaving the hoses connected. Next I released the 2 clips that hold the pump on, these clips also have a screw to secure them. I was then able to set the motor to the side without removing any wires.
The coupling parts had broken and were already off of the motor shaft and the input drive shaft of the transmission. I put the new drive parts on and had to tap them down untill they were flush with the end of the shafts. I then put the rubber coupling on the transmission drive end and aligned the motor drive to mate into the other holes in the coupling as I put the two back together. I then re attached the 2 motor clips with screws and reinstalled the pump with it's clips. I then reinstalled the cabinet onto the frame and replaced the cabinet clips. I then plugged in the lid switch connector and flipped the console back over and screwed it down. I then reinstalled the trim caps that had me stumped to begin with. The unit tested out OK.

Replaced motor starting capacitor. Noticed water leak at pump and replaced pump

Disconnected old power cord inside control cabinet, removed strain relief , then removed damaged power cord. Reinstalled new cord with new strain relief.

Purchased lid trigger elsewhere but got the connector on line here after being told I would need to purchase complete wiring harness to correct. Once lid trigger was in i stripped the three wires that went to lid trigger and pushed thru the back side of the connector. Then I plugged into trigger. Now washer works again. Very easy to do.

I disconnect power from wall outlets. Turn off pipes and remove water hoses from machine. Clear machine making room to operate.
I removed two Phillip head screws from behind the console, press down lightly on console then flipped it back. Disconnect the lid switch by releasing the plastic clip. Used a screwdriver to release the 2 metal holding clips (one on each side on top of machine. Ease the case up slightly then pull back gaining access to the centrifugal switch which is mounted to the motor with one Phillip head screw. One end of switch was broken and disconnected. Motor was not keeping up. Discharged capacitor by grounding the terminals with an insulated plyers. Lift the clip on the broken switch then pull the connector off. With new switch in hand, remove each of the 5 wires from the old switch by using a needle nose pliers one by one and connect them to the new switch making sure each one is properly secured in please. Connect the new switch to the motor using the single screw. Secure the connector to switch. Replace case by tilting back about 45 degrees, slide under front frame of machine all the way then down inplace. Use the two metal clips to secure frame to rear panel. Reconnect lid switch. Return machine to usual spot, reconnect water hoses, turn pipes on make sure there are no leaks. Plug back into wall outlet. Washer was tried and all cycles were completed.

The switch just snapped out of the holding section and the new part was snapped back into its place. He put the top section back on and it worked! Being a woman not knowing anything about repairing machines, I thought it went very well. I just googled my problem with the washer, it sent me to this site saying what they thought was the problem, I live chatted with someone and they confirmed the solution. I ordered the part and it came in 2 days and my husband fixed it. And now I have a working washer again. Thank you for your site. Anne

Sprayed wd40 - limescale - boiling water , NOTHING WORKED after half an hour reapeted spraying and pulling the tub and shaking it back and forth - still nothing
Finally I replaced the center nut loosely than putting a piece of wood on top of it and with me holding the tub slightly high - my wife than whacked it hard several times , I also was turning the tub every whack
When it came out it was full of rust and grime - it would have never come out without what we did
Replacing the the rubber washer was easy - machine works and no more leaking- thank you for your video which really helped to start the job