VBXR1060V1AA Hotpoint Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Olle J from Albert Lea, MN
- Parts Used:
- WH2X1197
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
Noisy washer, especially while spinning.
Take off front. Take off top. Pull off agitator. Pull off agitator coupler, after removing bolt holding in place. Attempt to remove hub nut, no joy. Wound up cutting the nut with a Dremel tool and chiseling the nut off. Closer inspection revealed a bad transmission. Due to the cost of the transmission, we will continue to use the machine until it completely fails.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Arthur D from COLUMBIA, MD
- Parts Used:
- WH49X10042
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
The agtator wasn't working to clean the clothes.
Got a new part in the Agitator Coupling Kit, as the existing part was worm down. Simply removed and inserted the plastic bottom, used a mallet to pound it down and it was finished. By checking a video, I felt comfortable in doing the repair myself. A greater feelings was knowing I didn't have to go out and buy a new clothes washer. Thanks PartSelect for having the right part to complete this project.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marci from Salt Lake City, UT
- Parts Used:
- WH49X10042
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
GE Profile Washer would not agitate but would still spin, etc.
I used the "belt" technique to remove the agitator. It was difficult at first to remove but after a few tugs on the belts that were looped under the plastic bottom, the agitator came up. Then I unscrewed the bolt holding the coupler. The agitator coupler kit purchased from PartSelect came with a new screw so I replaced the old coupler with the new one and fitted the new screw in it's place. I put the agitator dasher back on and then it worked perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mahlon from Northville, NY
- Parts Used:
- WH45X10027
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Base hub had broken into several pieces.
The repair was done as describe by others with the "hub nut" having to be cut off due to corrosion. Instructions for removal of the tub were found inside the control panel area on the left hand side. Ordering s new hub nut and cutting off the old one proved to be a necessity.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leisha from Trinity, NC
- Parts Used:
- WH49X10042
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
Washer would fill and drain, but not agitate the clothes, I kept getting a pile of laundry soap in the bottom of the washer and left with dirty clothes
Removed the screws, pulled out the tall skinny thing that rotates, pulled out the broken part, ordered the new one, replaced it, (you have to push down until it snaps into place) Put everything back together and had clean laundry within 45 minutes. Anyone can replace this part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lucas from hastings, MI
- Parts Used:
- WH49X10042
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
washer would not agitate
The part came very fast and was easy to install, I pulled off the agitator and removed one bolt, replaced worn out part with new part and put the new bolt that came with the part in. Reatached the agitator and washed some clothes. done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- akram from lakewood, OH
- Parts Used:
- WH49X10042
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Socket set
the washer would work but the agitator wouldnt spin
took out the agitator then removed the agitator coupli and found out that the coupli was worn out, i then replaced it and everything worked again
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Justin from New Orleans, LA
- Parts Used:
- WH49X10042, WH49X10042
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Agitator not working
I just added the agitator coupling and screwed it in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tom from Gaithersburg, MD
- Parts Used:
- WH49X10042
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Agitator was not moving (agitating)
I was very disappointed that this washing machine was broken since it is the second GE washer I have had in this house and the home is only 11 yrs old. I went to the Parts Select website and used the repair information to diagnose the problem and order the part. The part was about $12 including shipping and arrived in a few days. Installation was quick and easy. Overall a very good experience since I was asssuming a broken transmission and new washer. Thanks Parts Select!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Danny from Edwardsville, IL
- Parts Used:
- WH49X10042
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench set
clunking noise coming from agitator
Popped the agitator off, removed the bolt, pulled coupler straight up. Reversed steps. Done in under 5 mins.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Betty from Ventura, CA
- Parts Used:
- WH49X10042
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Washing machine did not agitate
My husband remove the agitator and found that it was worn. I googled the problem and one of the websites that came up was PartSelect. My husband watched the easy to follow video and had me order the Agitator Coupling Kit. It arrived in just two days. It took him 15 minutes to install and I started washing immediately. It cost us $13.22 and saved us $800 to $1200 if a new washing machine would of had to be purchased. The washer is 15 years old and now with this repair will hopefully continue to wash for a few more years! Thank you PartSelect!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- wilfredo from glendale, CA
- Parts Used:
- WH49X10042
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench (Adjustable)
Agitator is not turning
Agitator came off easily, but the agitator coupling was a little bit hard to remove. I have to yank it hard to be able to remove it. Putting the new part in is a bit hard too. I had to use a hammer to put it in. (with a piece of wood in between). Tried it with a small load and We're back in business. It was a pleasant experience to do business with you guys. Thanks for the quick turnaround.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brenda from Sachse, TX
- Parts Used:
- WH49X10042
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
The washer would fill with water, drain and spin but the agitator would not work. It would just wobble around.
To get the old agitator off I first used two pieces of laundry line rope to hook under the fins of the agitator on each side. Next I laid a 5 foot long 2 X 4 across the top and tied the ropes on. I filled the washer with 5 or 6 inches of extremely hot water to help loosen everything up and used leverage to pop the old agitator off. After that I used a socket set to remove the bolt from the top of the agitator coupling and took it out. I then put the new coupling in, replaced the bolt and lined up the agitator and slid it back on until it clicked and locked into place. The washer works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kevin from Saunderstown, RI
- Parts Used:
- WH49X10042
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Machine would not agitate. Everything else seemed to be working fine.
I removed the fabric softener cup and lifted up on the agitaotor till it slid off. I then removed the bolt that held the agitator coupling in place. I then worked the coupling off, wiggling it side to side until it slid off. Then I slid the new coupling on and replaced the bolt. Lined up the agitator and slid it back on. Then replaced the fabric softener cup. Job could not have been any easier.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- steve from gilbert, AZ
- Parts Used:
- WH49X10042
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Wrench (Adjustable)
agitator doesn't agitate
Slide rope beneath agitator.
Pull up with good force..agitator will separate from coupling.
Remove screw from coupling.
Slide coupling off.
Slide on new coupling.
Install screw included with the new agitator (Don't use old screw. The new one is a specialty part designed for new coupling)
Slide agitator back down over coupling.
Done
Pull up with good force..agitator will separate from coupling.
Remove screw from coupling.
Slide coupling off.
Slide on new coupling.
Install screw included with the new agitator (Don't use old screw. The new one is a specialty part designed for new coupling)
Slide agitator back down over coupling.
Done
Was this instruction helpful to you?
Thank you for voting!