VISR208DTAWW Hotpoint Washer - Instructions

Worked Perfectly

This model did not quite go as in the video on this site. The agitator just pulls up off the coupler. Removed the old, put on new, including new bolt that came with it, snapped the agitator back on, viola!

Popped the agitater off the coupler by using belt slipped under agitater and pulling up sharply. Unbolted coupler but it was stuck. Put agitater back on minus the bolt. Put a couple towels into washer ran a small load, soon as it started to agitate I could hear a sound and I found both pieces had came off the splined shaft. Hard part was over.

An easy fix. I was impressed with how fast I received the parts!1 Three days and that was during Christmas mailing season. I was very satified. Craig H. Tampa Florida

The washer did not Agitate although it did spin. So the motor appeared to be good. I noticed that you could rotate the agitator by hand, that didn't seem right. So I pulled the Agitator off the coupler. Now the coupler can rotate by hand around the spline shaft. I removed the bolt holding the coupler to the spline shaft. The spline shaft looked good. Ordered the new couple and installed it in 10 minutes. I was fortunate that the bolt came off easy. I didn't need to use the motor to assist in getting the bolt free.

The project was pretty easy. After removing the
11 screws on the inside of the door , the handle assembly was right in the open.I unplugged the 2 switches and installed the new handle.
Parts Select diagrams made it easy to find the right parts.
Thanks, Len

ordered replacement. received in two days and voila! Fixed!

The knob had broken off a few months ago. I didn't think to look for one on the internet. I finally googled the brand name and part number and your company came up. It had the picture of the part which I ordered immediately. It came in the mail really quickly. I was so excited when I received the knob. I took it out of the package and slipped it over the stem in less than a minute. It went on perfectly. Now I no longer need to use pliers to turn on the dryer. It looks great and I am no longer inconvenienced. I love the new knob and would do business with this company again.

First I removed the dasher by placing rope around the fins of the dasher. Wrapped the rope around a 2 x 4 approximately the width of the washer. Standing on the washer I pulled up on the board and presto. Up came the dasher, removed the bolt out of the bell, removed the bell. New part came in the next day after the order was placed! Great service. To install the new bell, used the new bolt sent with the part. Centered and aligned the dasher on the bell. Pushed down and locked in place. Turned on washer and started filling with water. Washed clothes within 15 minutes from start to finish.

Husband took the machine apart. We found your website - put in the parts number...and up pops a picture! Very cool! We ordered and the machine was fixed within 4 days - easy smooth! I would highly recommend this site. The part shipped out the day we ordered the part!

We were lucky, the agitator came off on its own. Removed the coupler which cracked when a sheet got stuck underneath it! Replaced coupler and new screw/nut combo, popped on agitator. That easy.

The repair was really simple. I pulled off the agitator cap by hand, then put my fingers under the agitator itself. There should be some play in how much the agitator can be lifted up. Some instructions and how-to videos tell you to use a leather belt to remove the agitator but I didn't have a problem removing it with my hands. One quick, hard pull did the trick. Under the agitator, you'll see the agitator coupling, which s held on buy a 7/16" bolt on top. Use a nut driver or a socket to remove the bolt and pull the coupling straight up. Use a wire brush to scrape away all the crud underneath it and on the metal splines. Once the area is reasonably clean, slide the new coupling into place and reattach it with the new bolt that is provided. Line up the grooves in the coupling with the grooves in the agitator and snap it back down into place. Replace the agitator cap and you're all done.

Viewed the step by step how to and was able to complete repair all has worked well great info sight!

Easiest repair ever. My wife actually did the repair because I thought I'd need more time to do it. She just pulled the agitator staight up and out then removed the bolt holding the coupling, pulled out the defective coupling and put the new one in, replaced the bolt, slid the agitator back on and it worked perfectly! Thanks for making a $60 or more repair call a $13 dollar self repair. And that includes shipping! We will always use your site for future fixes.

pulled out the center agitator, undid the nut , put the new one on , easiest repair ever, less that 13 dollars. and the part came in 2 days, wow, I am impressed with your company!!!!!