WLW3400SALAD Hotpoint Washer - Instructions

Tilted the washing machine, removed 4 hoses from the pump and the drive connector;
removed 3 nuts that hold the pump; install
the new pump and put back the hoses; to be safe, I unplugged the electric

I removed the four hoses that were connected to it, then I removed the three screws holding the pump in place. Then I removed the drive adapter that was connecting the pump to the motor. I then did everything in reverse order to install the new pump and everything worked just fine. Thanks!

After pulling the knob out ( on position) a white retainer clip was visible behind the knob. Using a paper clip bent in to a "J" shape I was able to easily remove the retainer clip and knob . The old knob had several stripped teeth that caused the problem. The new knob came with the retainer clip installed . The knob slipped on and locked in position.

Unplug the machine. Turn it face down. Take the back off. Take the four hoses off the pump. Unscrew the screw holding the connection to the motor and carefully slide the brace off without bending it. Remove the 3 screws holding the pump on. Take the old pump out. Screw the 3 screws back on. Attach the drive mechanism with the clamp carefully being sure to even it out under the clamp as you tighten it. Reattach the hoses. One of my hoses leaked after wards so I had to trim a half inch off to get a better grab on the pump. Put the back on and stand her up. Plug it in and test her out.

Husband did it. Tipped machine onto its front. Took out some screws and disconnected a wire and removed hoses from pump. Then put it all back and it is as good as new. This is the second pump in two years, but it beats the price of a new machine.
Your service is excellent. Both times, I have ordered the part is here the next morning. Never have had such service from anywhere else. I am telling all my friends about your web site.

had to pull knob out to see the clip locking the knob to the post.
finally got the clip out, pulled knob off sand put on new knob with new clip

Removed the back of the machine and then flipped the machine on the side and loosened the motor to get the old belt off. A piece came out so we had to check the schematics online to figure out where it went. We believe it was the out-of-balance cut off switch. So to fix that we unplugged the motor assembly and took it out. I also had to fish the spring out of the vacuum, no small task. The worst part was that the belt was so deteriorated that it was super greasy and the carpet ended up a mess. We replaced the motor and belt and now it actually gets the water out of the clothes. Simply Green cleaner was used for the rug and after some strong elbow grease it was cleaned. If not for the mess and the other part and the vacuum snafu, I would have labeled this as easy.

This was my daughter's washing machine. I looked at the back of the machine to see if there was an opening to get to the parts. Since the back is all closed up. I knew the front had to come off. I pride up, and I pride out, and finally the front popped off. After taking the front cover off the washer. I could see the belt was all chewed up. We ordered a new belt from partselect and got it a day early. I tried to pry the belt on without loosening up anything. I couldn't get it. So I loosened the four bolts on the motor mount and slid the motor backwards towards the other pulley. I put the belt on both pulleys and pried the motor forward to tightened the belt up. Then tightened all four bolts. Put the front guard back on and tried the washer to see if we had any other problems.

Repair was relativly simple. I read previous customer direction submissions. I found that laying the front of the washing macine down removing the back panel gave easy access to the water pump. Remove all 4 hoses first then with a 11/32nd socket remove the top 3 screws that are holding up the pump. At the bottom of the pump unscrew the clamp until the pump will slide out of the rubber stabelizer.(Leave stabelizer attached to the motor) Remove the pump and in reverse order replace with new pump leaving the back cover off of the machine. Set the washing machine upright and check for leeks. After checking for leeks attach the back panel onto the washing machine.

Viewed video on installation of new belt. A little awkward to get to the rear bolts, but used a wrench with success. Now washer spins correctly. Thank you.

Laid washer face down, unscrewed the 3 screws holding part to brackets. Removed the hose connections to the pump part. loosened the clamp around the base of the pump and pulled the part out. inserted new pump, tightened the clamp, reconnected the hoses, and bolted the part to the brackets. First time through, one of the hoses was not tight enough, so we put a new clamp on it and it worked fine.

repair was quick and part came quickly. I was very satisfied.

This repair was a no brainer repair. The factory replacement knob that I bought from this site comes with a new "D"-Ring. Some other aftermarket parts houses sell the knob and the "D"-Ring as seperate parts. The knob from this site already has the "D"-Ring ring installed in the knob. My "D"-ring was broken and I simply removed it with my fingers. All I had to do was properly align the new know knob with the timer shaft and press it into place. If your "D"-ring is not broken and not still inside the old knob, you will need to pull it off the shaft with a pair of pliers before pressing the new knob onto the timer shaft. Dr. "B" The Hot Rod Doc

Unfortunately, this washer doesn't have a front panel: to get to the belt, removed the back panel. Unfortunately, you can't get to the belt from there either, unless you turn the washing machine upside down. Since the top of the washer is not level (control panel sticks up), the washer needs to be tipped upside down onto something the washer lid rests on, but keeps the control panel off the ground. We used...a sled. Unfortunately, since it didn't drain the last time used, even though we bailed the tub, there was still a fair amount of water that drained out once upside down. This is a heavy washer - took 3 of us tipping it over carefully onto the sled. We unbolted the motor, put in new belt, but needed to put a piece of the shifter arm assembly in place, which came loose. Took 2 sets of hands to accomplish all this. Works now - 2 small loads of laundry done successfully.

i Had washer up side down took puly out and transmission seal out used screw driver install your part add seal on it tap it back in used socket added quartz of gear oil90 as recommended put every thig back it good experience and saved hundreds of dollars for new ones thank so much for ur video and ur technical people on your site