VWXR4100TAAB Hotpoint Washer - Instructions

Pulled off agitator with little effort. One 7/16 bolt to remove and the coupler came right off. Pushed on new coupler, replaced with new provided bolt, pushed agitator back on and was back in business!! Very simple inexpensive repair. Thanks Partsselect for your quick parts turnaround!

I had no intention of trying to fix the washer myself after reading about how to do it, only because I didn't know what half of the words were referring to. But once I watched the video, and I saw that the part was going to cost less than $15.00 (shipping included), I thought I would at least try it before going out and buying a new machine. The washer in the video was slightly different than mine, but I recognized the parts from my machine and mine was actually easier to replace than the one in the video. I just pulled off the agitator, unbolted the old agitator coupling and replace it with the new one, bolted it back on and lined up the agitator grooves with coupling and that was it. It worked and saved me a lot of money. I once had an appliance repairman tell me that if your washer or dryer lasts 7 years nowadays, you should consider yourself lucky. Mine is 7 years old, so I thought I would have to replace it. I didn't particularly want to pay someone $100.00 to come to my house and tell me it couldn't be fixed if I was going to have to buy a new one. But fixing it myself was very easy. Written instructions never would have worked for me, but the video was very helpful. Thanks!

Unplug power. Pull up firmly and quickly from the base of the agitator. Some videos used a rope and 2x4, I didn't have to. The agitator just pops right off. Then with a 7/16" wrench unscrew the bolt while holding on to the coupling. Take agitator coupling off. Clean off metal grooves that the coupling goes on, use either a small screwdriver, metal brush, a knowl, just to make sure you will have good connection with the new coupling. Then install the coupling, new nut, tighten nut firmly. Install agitator pushing down firmly on opposite sides until snaps in place. Turn agitator by hand, it should not free spin. Plug power back in, run washer with water and bleach only in the smallest setting and let it run through its cycle. This will take care of any black debris that might have got into the bowl while fixing. GOOD LUCK!! I also used videos found on Google.

I pulled up on the fin part of the agitator exposing the gear coupling. I unbolted the nut on top with a 12 mm socket. Once the nut and washer were removed I pulled up on the gear coupling and slid it right off. Reversed procedures to install the new one.

I noticed the agitator would spin all the way around, in each direction. Also, the machine would make no sound, associated with washing, during that part of the cycle. I pulled the fabric softener reservoir off, with fingers on each side of the agitator, i pulled straight up and that gives you access to the coupling. Use a 7/16'" socket to loosen the nut, remove it and pull the coupling off. Press the new coupling on the splined shaft, tighten nut, and line up agitator with the grooves, push it down and replace fabric reservoir. Straightforward repair.

took agitator off, loosened bolt on coupling, took that off. Replaced new coupling and tightened bolt on top. Put agitator on and pushed down hard to set in place. I'm a 66 year old female with no mechanical ability. I ordered this part on Sat. and it was on my door step on Mon. great service and video explained how to do repair and information provided possible repair needed. Great company.....

I pulled the top of the agitator off (the softener dispenser) then pulled the agitator itself off. I had to pull with some force. I used the socket wrench to remove the bolt on top of the agitator coupling. I then pulled off the old agitator coupling, replaced it with the new part. Used the socket wrench to tighten the new bolt. Lined up the slots on the new coupling with the agitator top, it slid on with a little resistance. The last part to replace was the softener dispencer.

Watch how to fix it on You Tube. Order the part I needed and fixed. Real simple. That is it.

There are many on-line videos to help you do this. It's so easy, even a beginner handyperson can do it. For this model, just run a strap under the agitator to assist you in lifting it up off the coupler (good tug). Remove the old worn coupler, put the new one on, set the agitator back on by giving it a little downward push.

Pulled agitator by hand, (very easy), removed bolt holding coupling to shaft, removed coupling and installed new one. Tightened bolt snugly and pushed agitator bank over coupling! About 5 minutes to repair!!!!!!!!!

Took the front panel off and it looked like everything was OK with the transmission, etc. Pulled out the agitator and noticed that the coupler had stripped out splines. New coupler was a later design, but was backward compatible with the new bolt included. Spline slipped on with no problem and hold down bolt snugged down just fine. Snapped the agitator back on and was in business.

at 1st, i call GE for service, but i have to wait for the next available field service engineer which is 7 to 8 days to come to my place to check on the washer. the cost is $99.00(non refundable) and then he will order the parts needed for repair another 2 to 3 days. then i decided to buy the parts myself online,and google the web on "how to fix the washer that stopped agitating" everythings in there,with video instruction. pull the agitator up and out by grabbing on to its base. inside, the knot was corroded and the o ring worn out,but really easy to remove with the 11mm socket. the coupling kit although looks different,fit perfectly. insert says its an upgrade of the old model. toss the old and replace with the new, no sweat! now it's shaking like crazy.

I used the video instructions sent to my email and everything worked perfectly as instructed.

The agitator is the tough thing to remove, I took a previous posters advice and used a rope and 2 boards to pull it up. I will describe it as many short ropes but it can be done without cutting the rope if you think a lot about it. loop the a rope under the agitator so its under 1/2, loop another rope under the other side. tie both loops so you can slide a board in each across the top of the washer. Then tie the 2 loops together on 2 sides down near the bottom of the agitator otherwise they will come out from under it when you pull. then slide the boards in the loops and lift up pulling up the agitator.That is the hard part. Remove the bolt on the coupling, and pull it off. The new one had to be lightly hammered on with a rubber mallet, then use the new bolt. the Agitator slide down and with a push down it popped on. Putting the new part on only took 15 min, removing the broken one took about 45 min. Washer is woking great now ! Saved over $100 or buying a new washer !