HTWP1000M1WW Hotpoint Washer - Instructions

I shut off the juice to the Washer, I then removed the 4 torx head screws in the panel, so I could gain access to the switch. I then unpluged a small hose going to the switch, then turned the switch by hand about half a turn & it came right out. I then replaced the switch with the new one by turning it half a turn in opposite direction, replaced hose, put the back panel back on, ran the machine to make sure it was working properly.
It is working fine, thanks to Part Select.com , fast service I would reccomend them to my freinds.

Removed the old one and installed the new pump, by removing the front cover and disconnect everything.

The after school director told me of the washing machine flooding. It took only a bit to find the hose that was leaking--a little longer to figure out where it went. It was the bleach line to the drum from the little bowl under the lid. It had pulled off.

I noticed that three of the four tub dampening straps (little rubber bungees) were broken. PartsSelect had a good exploded view of the washer that helped me locate the correct part and order it. They were shipped quickly.

Start with the machine empty of water and unplugged.

The front of the washer pops off (most have a removable top but this GE did the front instead). This exposes two screws to remove in order to lift and remove the top, exposing the tub. While you lift the lid, you have to remove the bleach line from the pocket at the front of the machine. It helped to unplug the machine and remove the lid switch to make access easier. It has two screws holding the assembly to the lid.

The straps are on the four corners of the tub, attached by hex-head screws. The two in the back aren't as easy to access. A stubby nutdriver would have helped for the screws that were upside down holding the straps to the frame. The straps were replaced and all the parts put back.

The washer is quieter and shakes much less. It was ready for the Christmas dinner washing later in the week.

I removed the bottom pan and found the problem , It was the drain hose , then I removed the hose , and began to look for a replacement part , and my search lead me to Parts Select .com , It was MOST helpfull and for that I thank you guys , I got my part and insalled it in about 15 min. and took the machine back into the laundry room hooked it up and it's been doin good sense .

First I found out on the web how to open the washer's front cover.
For the strap in the front, it's relatively easy to replace a strep if your hands are somewhat flexible.
For the one in the back, I also needed to open the top dial panel, in order to lift the main lid connected to it, in order to then be able to reach one of the screws of the back strap. the other one of its screws I was able to reach from the front with a ratchet and extension from the front. Arms do get heavy from time to time, but overall it was manageable.

Popped the front cover off and found a small hole was in the drain hose going to the pump,used pliers for one clamp and nut driver for the other clamp,removed bad hose and installed the new hose,ran water pump after putting some water in the tub,checked for leaks,put the front cover back on,that was it.

Very easy with your great instructions in my email. took the wires off,took the hoses off,then the two bolts,put the new one on and reasembled the hoeses wires and bolts. put the front back on and that was that. Your company is great thanks for all your help.If I ever need help again with any off my appliances i will call on you,agin thank you very much. Frank!

The first thought regarding the light rumble during the spin cycle is that the bearing was going bad. Many of the other inputs on replacing the bearing included the problem with removal of the Hub Nut. Only one article noted a set of assembly instruction for the washer is clipped onto the upper rear panel behind the control knobs, but I did not see this comment until later. Not being sure where to start with diassembling the washer, I began by taking off the control panel and to my pleasant surprise I found a neatly folded set of detailed instructions. Following the instructions, I proceeded to quickly disassemble the washer until I got to the HUB NUT. The Hub Nut is an aluminum, 1 -11/16 inch, left hand threaded problem. My tool selection is somewhat limited, so after unsuccessfully attaching it with grippers and vice grips, supported with the liberal aid of a rubber mallet and plenty of WD40, I went looking for something with which I could a better grip on the hub nut. The grippers and vice grips would slide a bit when hit with the mallet. Also since the space is very restricted, a large wrench could not be used. I located a 9-inch pipe wrench, and with the rubber mallet the Hub Nut finally loosened after just a few hits. I replaced the old bearing which appeared to be in fair condition. While replacing the bearing has not solved my noise problem, I thought that my experience with the pipe wrench benefit someone else in their efforts to get the hub nut off without using a chisel.

old one out, new one in. new one is seated, but not a perfect match bracket to hold hose in washer does not fit on this replacement hose properly. But I feel comfortable with the result & use

I googled "water not draining washer" and found a video made by Partselect.com on youtube on how to replace the water pump for a washer. So, I went to their website and punched in the model number of the washer and found the water pump I needed in stock. It said it takes an average of 1.8 days for delivery. I ordered it on a Sunday and by Tuesday I had the part delivered to my front door. That night after work, I went down to the washer which I already had sitting face down on the floor with the back peeled off and the pump out from the weekend so I could compare how it looked with the online pictures. The new part came already mounted on a new bracket so it was just a matter of installing the bracket and hooking up the intake and output hoses. In order to make my job easier in the tight space, I removed the drain hose from the bottom of the wash basin by squeezing the pressure clamp with a large pair of adjustable pliers. I then installed the other end of the drain hose to the pump itself. I then hooked out the end of the output hose to the other part of the pump that pumps out the water to the sink. I first removed the clamp on the back of the washer that held the output hose to the back of the washer. That gave me more leverage to move the pump around for the installation. Once both hoses were clamped onto the pump, I used a ratchet socket wrench to install the two bracket bolts directly onto the base of the inside of the washer in the same holes using the same bolts as the old pump. Once that was tightly installed, I Hooked the other ends of the two hoses to the bottom of the wash basin and to the back of the washer respectively. FInally, I connected the ends of the two wires into the clips on the pump in the same order as the original pump. One white one black. Finally I screwed in all the short sheet metal screws that held the back washing machine cover on. It was about 12 screws. I then installed the drain hose with the original bracket to the back of the washer. Satisfied that everything was installed tightly, I stood the washer up and then hooked the water hoses back up to the faucets and tightened them snugly with the large adjustable wrench to ensure it did not leak. I plugged the washer back in, hooked the drain hose to the sink and then filled the basin up partially. Moved the control to the drain mode, and the water came out wonderfully. Note, when the pump was broken, I was able to drain most of the water from the wash basin by lowering the drain hose the a bucket on the floor and letting gravity do the work of draining it. I had to fill the bucket several times and dump it into the sink, before I was able to drain all the water out and then lay the washer face down on the floor to remove the back of the washer. Thanks for the part and quick delivery. I saved a lot of money on repairs by doing it myself.

I have never done this repair previously, and it was simple and easy, but I didn't know that until I watched your video. Several days after placing the order for the part, it came & I followed your video instructions, and voile! Washer works like new again. I can't thank you enough for your video instructions & making all these parts available. PLEASE keep it up!

After much research I decided to have to repaired all new models were not good. Reached out to local service repair because I beleved that it was the timer. $270 for service call REALLY and $125 for part.
Reached ot to PART SELECT LOVE YOU GUYS) SAID WHAT WAS THE PROBLEM the chocie was a new knob or replace timer. I am
83 yr old woman and believe I could have done it myself if it wasn't for the problem of moving the dryer out. shut off electric four screws
take out old replace new rewire the four screws WORKING NEPHEW
DID IT IN TEN MINUTES NO CHARGE BUT THANK YOU PART SELECT FOR REAFFIRMING MY DIAGNOSIS. AUDREY

Removed front panal & operate to see leak origion. Found the side of the pump cracked and split. Part Select sent the exact replacement part! Unplug washer. Remove ront panal; using a putty knife and a bit of preasure at the two release clips. Using pliers or small vise grips, squeeze hose clamps and locate back out of the way and remove two hoses. Have a shallow pan below to catch remainig water. Unhook the electric connections, taking note of where. Using nut driver or small ratchet, remove the two mounting screws and pump. I used new screw type hose clamps in lieu of the originals.

followed video

Watched the video, read installation instructions.
Replaced four broken dampening straps, washer is quiet and all is good.