Models
>
VVSR1030H5WO
VVSR1030H5WO Hotpoint Washer
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for VVSR1030H5WO
Viewing 4 of 4
Keep searches simple, eg. "belt" or "pump".
This clip fits inside the control knobs for your laundry machines, and helps to securely fasten the knob to the shaft, which allows you to easily turn the knob to select the correct settings. This is ...
No Longer Available
$33.95
This is a genuine OEM drain hose for your top-load washing machine. It is made with a flexible and corrugated black material, and measures 57-inches in length. The purpose of the drain hose is to move...
In Stock
Order now and your part arrives by Sep 11
$20.72
If your washer is leaking when it is filling or agitating, you may need to replace the tub seal. The tub seal is found between the transmission and the outer tub in your washing machine. This genuine ...
In Stock
Order now and your part arrives by Sep 11
$14.16
This is a genuine OEM replacement knob and clip for your laundry machines, and fits onto a D-shaped shaft. Over time and with regular use, it is possible that the knob will crack and no longer be capa...
In Stock
Order now and your part arrives by Sep 11
In Stock
Order now and your part arrives by Sep 11
$41.95
The tub bearing secures the spin basket in the tub assembly of a washer. It is located on the bottom of the outer tub. A common symptom of a worn tub bearing is a very loud noise (including a grinding...
In Stock
Order now and your part arrives by Sep 11
$28.91
Bolt not included. This part connects the transmission drive shaft to the agitator base.
In Stock
Order now and your part arrives by Sep 11
In Stock
Order now and your part arrives by Sep 11
$25.95
This replacement inlet drain hose connects your washer's water pump to its tub. This hose is seven and a half inches in length and only two inches wide.
In Stock
Order now and your part arrives by Sep 11
$25.10
This part is a replacement control knob for your washer. The control knob allows you to select the desired setting for your wash cycle. If your washer will not start or the timer will not advance, you...
In Stock
Order now and your part arrives by Sep 11
$15.26
This part is a replacement socket rod support for your washer. The socket rod support is found at the top of the washer frame in the front part of the washer. It supports the suspension rod, so the ro...
In Stock
Order now and your part arrives by Sep 11
Common Problems and Symptoms for VVSR1030H5WO
Viewing 13 of 13Leaking
Fixed by these parts
How to fix it
Will not agitate
Fixed by these parts
How to fix it
Will Not Start
Fixed by these parts
How to fix it
Shaking and Moving
Fixed by these parts
How to fix it
Burning smell
Fixed by these parts
How to fix it
Spinning Issues
Fixed by these parts
How to fix it
Will not drain
Fixed by these parts
How to fix it
Noisy and Marks Left on Clothes
Fixed by these parts
How to fix it
Marks left on clothes
Fixed by these parts
How to fix it
No hot or cold water
Fixed by these parts
How to fix it
Draining Issues
Fixed by these parts
How to fix it
Noisy
Fixed by these parts
How to fix it
Timer Not Working
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Victor from League City, TX
- Parts Used:
- WH38X10002
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Bearing on the transmission to tub wore out (mostly due to the washer not being level)
The back of the control panel had an instruction pamplet that was very useful. 2 parts did not go as written tho. To "pop" the spinner out, required short 1x4s and a shake/shingle bar to pry it up and the wedging of the 1x4s under it, until enough strain was put on it to "pop" it off. Then the large 1&11/16 nut was a bear. It require
... Read more
d a short pipe wrench (so it fit in the tub) and a hammer to brake it loose.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from Bloomington, IN
- Parts Used:
- WH38X10002
- Difficulty Level:
- Easy
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Leaking oil into the washer (in tub and on clothes)
Had never repaired a washer before, but have several tools and enjoy working with my hands. Knew it would be cost prohibitive to call a repairman, and didn't have anything to lose. Quick delivery from partselect -- reasonable price, too. This was as easy as simply taking the whole washer apart (NOTE -- there are instructions behind the kn
... Read more
obs inside the unit that are very helpful!) replacing the transmission and putting it all back together. Hardest part was getting the hub nut off of the transmission axle. To get it off (REVERSE THREADED, so 'tighten' to 'loosen') I used a 1 11/16 socket and impact wrench. Use the same tool to tighten (but go EASY...don't overtighten). This was not difficult, but just took some time. A couple of evenings later, we were washing again like NEW. Part cost around $160, labor was 'free' and much less than a new $500 top loader or $800 front loader. If you enjoy taking things apart and have some tools, then go for it!
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- PETER from MCMURRAY, PA
- Parts Used:
- WH38X10002
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Socket set
oil leaked on clutch and slipping
followed the instruction on the wiring sheet and removal and repair sheet that comes with the wahing machine. They wee very good directions and the only problem that I had wa getting the 1 and 11/16 inch not off the shaft that holds the tub to the transmission, The main problem was that the transmission had leaked all over the break and t
... Read more
he tub would spin while hitting the pipe wrench with a claw hammer. Ended up using a 10 lb sledge hammer to hit the pipe wrench and that finally loosened up the nut, but that was the only real problem i had. I say this was easy except for getting off that nut
Read less
Was this instruction helpful to you?
Thank you for voting!