HLSR1090J8WW Hotpoint Washer - Instructions

Removed the front of the washer, screwdriver used. Disconnected the electrical wires from the pump. Removed the two bolts from the water pump bracket, socket wrench used. Disconnected the pump to exterior drain hose, plumbers wrench used to loosen tension clips. Drained all the water out of the washer tub, not easy not very neat. Disconnected the washer tub to water pump drain hose. Removed debris that was in the hose. Then connect the hoses to the new pump, bolted the bracket back in place, put the front of the washer back on.

replaces as per video. Very helpful

Easiest thing I ever did on the computer. U tube helped me diagnose the problem and how to remove the old pump and install the new. Parts Select menu was easy to navigate and had a picture of the pump I needed. The cost was affordable and I got the satisfaction of making the repair myself.

removed front of washer and removed top of washer very easy to replace 4 dampening straps (2 straps were broken replaced all 4

Removed front panal & operate to see leak origion. Found the side of the pump cracked and split. Part Select sent the exact replacement part! Unplug washer. Remove ront panal; using a putty knife and a bit of preasure at the two release clips. Using pliers or small vise grips, squeeze hose clamps and locate back out of the way and remove two hoses. Have a shallow pan below to catch remainig water. Unhook the electric connections, taking note of where. Using nut driver or small ratchet, remove the two mounting screws and pump. I used new screw type hose clamps in lieu of the originals.

old one out, new one in. new one is seated, but not a perfect match bracket to hold hose in washer does not fit on this replacement hose properly. But I feel comfortable with the result & use

removed back off washer, disconnected pump from washer tub, remove old pump in about 5 min, then installed new pump in less than 5 min. washer is working just fine wife thank me it was about 2 wks since the washer was down.

Very easy with your great instructions in my email. took the wires off,took the hoses off,then the two bolts,put the new one on and reasembled the hoeses wires and bolts. put the front back on and that was that. Your company is great thanks for all your help.If I ever need help again with any off my appliances i will call on you,agin thank you very much. Frank!

The first thought regarding the light rumble during the spin cycle is that the bearing was going bad. Many of the other inputs on replacing the bearing included the problem with removal of the Hub Nut. Only one article noted a set of assembly instruction for the washer is clipped onto the upper rear panel behind the control knobs, but I did not see this comment until later. Not being sure where to start with diassembling the washer, I began by taking off the control panel and to my pleasant surprise I found a neatly folded set of detailed instructions. Following the instructions, I proceeded to quickly disassemble the washer until I got to the HUB NUT. The Hub Nut is an aluminum, 1 -11/16 inch, left hand threaded problem. My tool selection is somewhat limited, so after unsuccessfully attaching it with grippers and vice grips, supported with the liberal aid of a rubber mallet and plenty of WD40, I went looking for something with which I could a better grip on the hub nut. The grippers and vice grips would slide a bit when hit with the mallet. Also since the space is very restricted, a large wrench could not be used. I located a 9-inch pipe wrench, and with the rubber mallet the Hub Nut finally loosened after just a few hits. I replaced the old bearing which appeared to be in fair condition. While replacing the bearing has not solved my noise problem, I thought that my experience with the pipe wrench benefit someone else in their efforts to get the hub nut off without using a chisel.

followed instructions on you-tube. shut off water faucets. disconnect hoses from washer. remove three hex screws from back of control panel. lean panel forward and slide to the right, then remove it and lay it down.
remove the two screws that hold the valve to the machine. use pliers to slide the clamp back and remove the hose. repeats these steps in reverse to finish job.
the first valve that partselect shipped leaked from the hot water hookup and was deemed to be defective. partselect credited my account before the part was at their warehouse. great service all around.

After much research I decided to have to repaired all new models were not good. Reached out to local service repair because I beleved that it was the timer. $270 for service call REALLY and $125 for part.
Reached ot to PART SELECT LOVE YOU GUYS) SAID WHAT WAS THE PROBLEM the chocie was a new knob or replace timer. I am
83 yr old woman and believe I could have done it myself if it wasn't for the problem of moving the dryer out. shut off electric four screws
take out old replace new rewire the four screws WORKING NEPHEW
DID IT IN TEN MINUTES NO CHARGE BUT THANK YOU PART SELECT FOR REAFFIRMING MY DIAGNOSIS. AUDREY

1) Remove the load size dial by simply pulling it off gently. 2) To gain access to the switch, you must remove the "splash panel" where the dials are located. Do this by removing 3 hex screws from the back of the splash panel. **(If you need to move the washer, do so with the tub empty. This will make it easier to move and also lessen the chance of damaging the floor due to excess weight - water weighs 8 lbs per gallon - the average washer hold from 10-15 gallons on the largest load). 3) Once you have access to the rear of the panel, you will notice 3 hex-head screws holding the splash panel to part of the galvanized metal washer frame. Remove these screws and make sure you place them where you won't lose them. Slide the back splash section to the right a little and then lift the back splash away from the washer. 4) Remove the plastic tubing located on the brown/orange section of the switch. 5) Now, gently press the female connector from the switch by gently pushing it away from the area where the tubing was and pull at the same time. 6) To remove the switch from the back splash, turn the switch in a clock-wise direction (do this carefully so the delicate section of the back splash doesn't break.) 7) Inspect the tubing to see if it has expanded while being on the pressure switch - If so, use a very sharp knife (carefully) to cut off that old piece. 8) Take the new switch and install it by getting it in the correct position (you can tell because the metal frame of the switch has two ears that help you to align the switch correctly) Twist the switch in a anti-clockwise direction until it snaps in place. 9) This step can be skipped if the "snap in place" works and the switch is firmly seated. IF, at some time or other, the nubs that are used to hold the switch in place have been damaged, you will have to replace the back splash (Prt # PS2340063) and this costs more than the switch. 10) If you are here without reading step 9 - Congratulations! 11) Make sure you replace the electrical connector onto the new switch (it only fits one way so if at first you are having trouble, try turning the connector 180 degrees. Once all the parts you disconnected from the pressure switch are back in place properly, place the back splash back onto where it came from. Replace the 3 hex-screws that hold the back splash to the machine and before replacing the machine to where you pulled it out from, run a test to get the pressure switch "pressurized." My suggestion is to set the switch at the setting where the water only fills for a medium load. (This next part is not necessary but is eco-friendly) Set the other dial so you only are using COLD water. Start the water loading into the tub (DO NOT have any material in the tub or the switch will not be set properly) and watch the water level to make sure it shuts off at the correct level. If not, don't worry, Just shut the machine off and turn the dial to Spin to empty the water. Do this while the lid is closed so you can tell when all the water has been emptied; there will be an unmistakable change in the sound of the pump. Start the COLD cycle over again and watch the water level; it may shut off the flow if the pressure switch has been pressurized correctly. If not, repeat the procedure once more. Again, if it shuts off properly, you can now try a load of clothes (keep it at the medium setting). After the clothes have gone through the complete cycle, the pressure switch may have reset itself and the next load will seem to have less water. Simply set the water level to its highest level and you are now all set to wash all the towels you used to soak up the water from the overflow. ONE MORE THING - If the pressure switch doesn't fix the problem, you will need to replace the valve assembly.

Removed front with putty knife to unlock hinge.removed and checked pump removed hose clamps with wrench and nut driver replaced hose reverse procedure

Take off front. Take off top. Pull off agitator. Pull off agitator coupler, after removing bolt holding in place. Attempt to remove hub nut, no joy. Wound up cutting the nut with a Dremel tool and chiseling the nut off. Closer inspection revealed a bad transmission. Due to the cost of the transmission, we will continue to use the machine until it completely fails.

I followed previous parts select customers advice exactly, of replacing the dampening straps, and it worked perfectly. Thanks-A-Million!